Skip to main content

Protrack - VT05C Configuration

This page covers the public configuration context for using the Protrack VT05C with Plaspy. It collects the practical, publicly available settings and SMS commands used to point the VT05C to Plaspy so the device can send live location and event data into your Plaspy account.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools. The VT05C supports SMS based configuration as shown below; follow the manufacturer documentation when in doubt.

Configuration Overview​

This configuration process prepares the VT05C to communicate reliably with Plaspy by assigning the correct APN and server endpoint, setting reporting intervals, and enabling GPRS operation when required. The example commands provided are the public SMS commands commonly used to configure this model.

  • Configure the device APN so the tracker can establish cellular data connectivity.
  • Point the tracker to Plaspy server settings so telemetry is delivered to the platform.
  • Set reporting intervals to control how often position and event data are sent.
  • Enable GPRS mode so the unit uses the cellular data channel rather than SMS for live updates.
  • Verify settings and device status using the tracker status and parameter check commands.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol
  • All devices in Plaspy use the same port for data ingestion

Typical Requirements Before Setup​

  • A valid SIM card installed in the VT05C with a data plan and the correct APN for the carrier
  • Ability to send SMS messages to the tracker for SMS based configuration
  • Access to the device installation location and a reliable power connection for the wired tracker
  • The official Protrack configuration method or installer tool documentation for the VT05C
  • A Plaspy account or access to the Plaspy platform to validate the device after configuration
  • Patience to confirm settings after firmware changes or hardware revisions

How This Tracker Connects to Plaspy​

When configured, the VT05C sends position and event messages to the shared Plaspy server endpoint and port so the platform can process and visualize data for monitoring and reporting. Plaspy receives the tracker data, automatically detects the protocol, and makes the device visible in your account without requiring per device port changes.

  • The tracker uses the configured APN to open a GPRS data session for reporting
  • Telemetry and event messages are sent to d.plaspy.com or the Plaspy server IP on port 8888
  • Transport can be UDP or TCP depending on the device configuration choice
  • Plaspy automatically detects the tracker protocol and ingests data on the shared port
  • Platform visibility includes live location, event alerts, and recorded history for playback

Common Configuration Workflow​

  1. Access the official Protrack VT05C configuration method such as SMS commands or the vendor tool described in the manufacturer documentation.
  2. Configure the SIM APN for the carrier so the device can establish GPRS connectivity.
  3. Enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138 in the device server settings.
  4. Set the server port to 8888 in the device configuration.
  5. If required by the device, choose UDP or TCP as the transport protocol.
  6. Save or apply the configuration and, if necessary, restart the device to activate changes.
  7. Validate that the VT05C reports to Plaspy and appears in your Plaspy account or dashboard.

Example Configuration Commands​

The VT05C can be configured via SMS commands sent from a mobile phone. Preserve placeholders when you replace them with carrier values.

  • Configure your carrier APN
APN,[apn]#

or, if username and password are required:

APN,[apn],[apnu],[apnp]#

Explanation: Replace [apn] with the carrier APN. Use [apnu] and [apnp] if your SIM requires an APN username and password.

  • Setup the GPRS server to point to Plaspy (domain and port)
SERVER,1,d.plaspy.com,8888,0#

Explanation: This command sets the primary GPRS server to the Plaspy domain and port shown above. Keep the command parameters in the order required by your device.

  • Set the update reporting interval
TIMER,60,60#

Explanation: Example interval command. Adjust the numeric values to the reporting frequency required by your policy or installation.

  • Switch the device to GPRS mode
GPRSON,1#

Explanation: Enables GPRS so the device uses the data channel to send telemetry to Plaspy.

  • Verify configuration and status
PARAM#
STATUS#

Explanation: Use PARAM# to query current configuration parameters and STATUS# to request operational status from the tracker.

Note: Send these SMS commands in the sequence shown above when following a typical setup flow. Manufacturer firmware or command syntax may differ; consult the official Protrack documentation for exact behavior.

Configuration Notes​

  • Manufacturer firmware versions and hardware revisions may change command syntax or available features; always confirm with the official Protrack documentation.
  • This tracker supports SMS based configuration as a public method, but vendor tools or configuration utilities may also be available for bulk or installer setups.
  • Choose UDP or TCP according to installer preference and device support; Plaspy accepts data on either transport and will detect the tracker protocol automatically.
  • Plaspy uses the same port for all supported devices so you only need to set port 8888 when configuring servers for the VT05C.
  • If you change APN or carrier settings, revalidate GPRS connectivity and server reporting in Plaspy after applying changes.

Why Use Plaspy with This Configuration​

Using the Protrack VT05C with Plaspy gives operations and fleet managers a straightforward way to collect live location and event data in a single platform. The VT05C's wired power design and tamper detection features complement Plaspy's visibility tools, enabling timely alerts, historical route playback, and centralized monitoring for vehicles and motorcycles.

To learn more about Plaspy visit https://www.plaspy.com. Verify the latest device specific configuration methods, firmware behavior, and manufacturer details on the Protrack website http://www.protrackgps.in/ to ensure commands and workflows remain current.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy