Skip to main content

QuecLink - GV53MG Configuration

This page describes the public configuration context for using the QuecLink GV53MG tracker with Plaspy. It collects the shared server settings used by Plaspy and practical setup guidance derived from the public device configuration content, including the SMS commands commonly used to provision the GV53MG for reporting to Plaspy.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data arrives. Manufacturer side steps can differ by firmware version, hardware revision, installer tools, or regional variations. The GV53MG supports SMS based configuration and GPRS server configuration commands in public guidance, and this page includes those example commands with explanations for each step.

Configuration Overview​

Preparing the GV53MG for Plaspy primarily means pointing the device at Plaspy's server endpoint, ensuring cellular data or SMS provisioning is available, and enabling the reporting parameters that meet your update and event needs. The commands shown later are public SMS examples used to set timezone, APN, server endpoint, reporting interval, and input behavior.

  • Configure the device to send telemetry and location messages to Plaspy server d.plaspy.com or the equivalent server IP
  • Set the device APN and authentication placeholders so the tracker can use mobile data for GPRS reporting
  • Define a regular reporting interval so Plaspy receives timely position updates and events
  • Enable relevant inputs such as an SOS or tow alarm so events are reported to the platform
  • Validate connectivity and confirm the device is visible in Plaspy after applying settings

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP — the device may be configured using either UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when messages arrive
  • Plaspy uses the same port 8888 for all supported devices to simplify configuration

Typical Requirements Before Setup​

  • Device powered and accessible for SMS or manufacturer configuration tool access
  • Active SIM card with data enabled and correct APN details for the target mobile operator
  • Device password or access credentials where required for SMS provisioning or the manufacturer management tool
  • Knowledge of the APN values to replace placeholders such as [apn], [apnu], and [apnp]
  • A way to receive device reports in Plaspy so you can validate successful registration and telemetry delivery
  • Access to the official QuecLink configuration reference or installer documentation for the GV53MG

How This Tracker Connects to Plaspy​

The GV53MG is configured to report buffered and live telemetry to Plaspy by sending GPRS messages to the shared Plaspy server endpoint and port. Plaspy ingests messages over TCP or UDP, automatically recognizes the protocol, and makes the device visible on dashboards and alerts.

  • The device sends location and telemetry messages to the Plaspy server endpoint d.plaspy.com or 54.85.159.138 on port 8888
  • Plaspy automatically detects the tracker protocol so the device can use UDP or TCP as configured
  • Event alerts such as SOS or input triggers are transmitted to Plaspy for immediate notification
  • Buffered messages are delivered when connectivity resumes so Plaspy receives queued position and event data
  • Regular reporting intervals ensure continuous visibility and historical position tracking in Plaspy

Common Configuration Workflow​

  1. Access the official QuecLink configuration method for the GV53MG such as SMS provisioning or the supported manufacturer tool
  2. Provide or confirm the device password for SMS commands if required the default password in public examples is queclink
  3. Enter the Plaspy server as d.plaspy.com or the alternate server IP 54.85.159.138 in the device server configuration
  4. Set the port to 8888 and choose UDP or TCP if the device requires a transport selection
  5. Set the APN and related credentials using the placeholders [apn], [apnu], and [apnp] as appropriate for your SIM
  6. Apply or save the configuration and restart the device if required by the tracker
  7. Validate that the device reports to Plaspy and that location and event messages appear in the platform

Example Configuration Commands​

The following SMS style commands are public examples for provisioning the GV53MG. They use the device password parameter as shown. The default password used in these examples is queclink. Send the commands as SMS messages to the device phone number or use the manufacturer provisioning channel.

  1. Optional initial factory reset
AT+GTRTO=queclink,4,,,,,,FFFF$

This command restores factory settings. Use only when an initial factory reset is required.

  1. Set the time zone to UTC 0
AT+GTTMA=queclink,+,0,0,0,,,,,,FFFF$
  1. Set the operator APN
AT+GTBSI=queclink,[apn],[apnu],[apnp],,,,,FFFF$
  • [apn] placeholder is the carrier access point name
  • [apnu] placeholder is the APN username if required by the SIM provider
  • [apnp] placeholder is the APN password if required by the SIM provider
  1. Set the GPRS server to Plaspy using both domain and IP with port
AT+GTSRI=queclink,4,,1,d.plaspy.com,8888,54.85.159.138,8888,,0,0,0,,,,FFFF$

This command configures the device to report to Plaspy using d.plaspy.com and the server IP 54.85.159.138 on port 8888.

  1. Set the update interval to 60 seconds
AT+GTFRI=queclink,1,1,0,0,,,60,60,60,60,7F,40,0,,,FFFF$
  1. Enable SOS button notification on input 2
AT+GTSOS=queclink,2,2,,0,0,0,0,0,0,,,FFFF$

Notes about commands

  • Preserve the device password parameter where required by the command syntax. The public examples use queclink as the password.
  • Send each command as a separate SMS unless your provisioning workflow supports batch commands.
  • Commands and exact parameter formats can differ by firmware version. Confirm with official QuecLink documentation if unsure.

Configuration Notes​

  • SMS based provisioning is shown in the public guidance here, but manufacturer tools or configuration software may offer an alternative method
  • Firmware and hardware revisions can change accepted command formats or available parameters so confirm commands against the current device firmware documentation
  • Choose UDP or TCP based on your deployment needs and network reliability considerations. Plaspy will automatically detect the protocol used
  • Plaspy requires port 8888 for all devices so use that port when configuring the GV53MG
  • Keep APN placeholders [apn], [apnu], and [apnp] available for operator specific values and do not share sensitive credentials in public channels

Why Use Plaspy with This Configuration​

Using the GV53MG with Plaspy provides a compact, secure path for vehicle location and event reporting. With Plaspy ingesting messages on the shared server endpoint and port, fleets get consistent visibility, buffered message handling, and event notifications that support recovery and operational workflows.

To learn more about Plaspy and how it supports device integration and fleet management visit https://www.plaspy.com. For the latest device specific commands, firmware notes, and configuration references verify details on the QuecLink official site https://www.queclink.com/ as manufacturer specifications and setup methods may change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy