Skip to main content

Reachfar - RF-V20 Configuration

This page documents the public configuration context for using the Reachfar RF-V20 GPS tracker with Plaspy. It focuses on the practical server settings and high level setup steps required to get the tracker reporting location and status to Plaspy, while avoiding firmware or vendor-specific tool details that vary by revision or vendor.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, which simplifies platform integration. Manufacturer side setup steps can differ depending on firmware, hardware revision, installation type, and the vendor configuration tool you use, so always confirm device specific operations with Reachfar documentation when needed.

Configuration Overview​

The goal of configuring the RF-V20 for Plaspy is to point the device to the Plaspy server endpoint, confirm transport settings, and validate that the device appears and reports in the Plaspy platform. Once configured, the device will deliver location updates and alerts to Plaspy for monitoring and operational use.

  • Configure the RF-V20 to send data to the Plaspy server endpoint and port
  • Ensure the device has a working SIM and mobile data connection compatible with GPRS TCP/IP
  • Validate transport selection (UDP or TCP) and save the device settings
  • Confirm the tracker is visible and reporting in Plaspy after configuration
  • Keep manufacturer documentation and firmware notes handy for troubleshooting

Plaspy Server Settings​

Use the following public server settings when configuring the RF-V20 to report to Plaspy. Plaspy uses the same port for all supported devices and the platform will automatically detect the tracker protocol.

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888
  • Transport: support for UDP or TCP; configure the device for either UDP or TCP if the tracker requires a transport selection
  • Protocol detection: Plaspy automatically detects the tracker protocol so the platform can interpret the incoming data

Typical Requirements Before Setup​

  • Confirm the RF-V20 has sufficient battery charge or is connected to a power source for configuration and testing
  • Ensure a valid SIM card with active data service is installed and any required APN settings are available
  • Access to the official Reachfar configuration method or software supplied by your vendor or installer
  • A basic understanding of how your chosen configuration channel works, for example SMS commands or desktop/mobile configuration utilities if provided by the manufacturer
  • Physical access to the device or remote configuration ability if supported, plus any required passwords or unlock codes
  • Network coverage in the installation area so the device can establish a GPRS connection

How This Tracker Connects to Plaspy​

The RF-V20 sends location and event data over the cellular data network to the Plaspy server endpoint and port listed above. Plaspy receives the device traffic on a shared port and identifies the tracker protocol automatically so the device becomes visible in the platform without per-device server differences.

  • The tracker is configured to report to the shared Plaspy server endpoint (d.plaspy.com or 54.85.159.138) on port 8888
  • Data transport can use either UDP or TCP depending on the device configuration and network conditions
  • Plaspy automatically detects and parses the tracker protocol once messages arrive
  • After successful configuration the device will appear in Plaspy and report locations and alerts for monitoring
  • Validate reporting to ensure location updates and alarms are reaching Plaspy as expected

Common Configuration Workflow​

  1. Access the official Reachfar configuration method or software provided by the manufacturer or vendor
  2. Enter the Plaspy server address either as the domain d.plaspy.com or the IP 54.85.159.138
  3. Set the destination port to 8888 to match Plaspy server settings
  4. Choose the transport option UDP or TCP if the RF-V20 requires a transport selection
  5. Apply or save the new configuration in the device or vendor tool
  6. Restart or power cycle the device if the configuration workflow requires a reboot to activate settings
  7. Validate that the RF-V20 is reporting to Plaspy and visible in the platform

Example Configuration Commands​

The RF-V20 modelConfiguration content for public commands is not included here, and manufacturers provide different command sets or configuration utilities. Exact command syntax and configuration messages vary by firmware and vendor tool. For SMS, web or desktop configuration tools supplied by Reachfar or resellers, consult the official Reachfar guidance for the precise commands or UI steps.

If you need command examples for your firmware revision, refer to Reachfar provided documentation or the configuration tool supplied with your device.

Configuration Notes​

  • Firmware and hardware revisions can change available commands and menu layouts; always check the device firmware version before following setup steps
  • TCP versus UDP choice may depend on network reliability and vendor guidance; Plaspy accepts either and will detect protocol automatically
  • All devices in Plaspy use the same port which simplifies server entry across different tracker models
  • Confirm SIM APN and mobile operator requirements as part of the connectivity checklist
  • Use manufacturer documentation for any reset or recovery procedures if a configuration step fails

Why Use Plaspy with This Configuration​

Configuring the Reachfar RF-V20 to report to Plaspy provides a straightforward way to centralize location visibility, alerts, and operational monitoring for vehicles or assets. Plaspy’s shared server settings and automatic protocol detection reduce per-device server complexity, making deployment and scale easier for fleets and installations.

To learn more about Plaspy and supported integrations visit https://www.plaspy.com. For the most current device specific setup steps, firmware behavior, and manufacturer details verify information on the official Reachfar website https://www.reachfargps.com/ as manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy