Skip to main content

Reachfar - V55 Configuration

This page documents the public configuration context for using the Reachfar V55 GPS tracker with Plaspy. It focuses on the practical server settings and setup workflow that make the V55 visible on the Plaspy platform while highlighting the shared Plaspy server values you will apply during commissioning.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and the vendor configuration tool you use, so treat the instructions here as practical public guidance that complements the V55 product manual.

Configuration Overview​

This section explains the purpose of configuring the V55 for Plaspy and what you should expect after successful configuration.

The configuration process prepares the V55 to send position and telemetry data to the Plaspy ingestion endpoint, ensures the device can establish a reliable connection over the cellular network, and validates that Plaspy receives and displays the device in the platform.

  • Point the V55 to the Plaspy server endpoint so it can deliver GNSS, Wi‑Fi, and LBS location data to your Plaspy account.
  • Ensure the device has an active cellular connection and correct APN or network settings to reach Plaspy.
  • Select the transport method supported by the device (UDP or TCP) and set the Plaspy port so the V55 communicates on the same port used by all devices in Plaspy.
  • Save and apply settings, then validate that Plaspy receives the first reports and that location updates appear in the platform.

Plaspy Server Settings​

Use the following public Plaspy server settings when configuring the V55. These values are the standard endpoint details Plaspy expects for device reporting.

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on what the device or firmware requires
  • Plaspy automatically detects the tracker protocol so the platform can interpret messages from the V55
  • All devices in Plaspy use the same port so set 8888 consistently when configuring any supported tracker

Typical Requirements Before Setup​

Prepare the following items before you begin configuring a V55 for Plaspy.

  • A powered V55 device with battery charged or connected to vehicle power
  • An active cellular SIM with data enabled and any required APN information for the network in your region
  • Access to the official Reachfar configuration method or software recommended for your unit (web tool, desktop tool, SMS commands, or mobile utility depending on the model and firmware)
  • The Plaspy server address d.plaspy.com or the IP 54.85.159.138 and the port 8888 noted for input into the device
  • Administrative access to Plaspy so you can confirm the device arrives in your account and adjust reporting or geofence settings as needed

How This Tracker Connects to Plaspy​

When configured, the V55 is set to send its positioning and supporting telemetry to Plaspy so operators can view live locations, historical tracks, and receive alerts.

  • The V55 reports GNSS fixes plus Wi‑Fi and LBS assisted fixes to the shared Plaspy server endpoint
  • Data is sent to d.plaspy.com (or 54.85.159.138) on port 8888 using the selected transport UDP or TCP
  • Plaspy ingests the incoming messages and automatically detects the tracker protocol for parsing
  • Once visible in Plaspy, the device provides real-time location updates, event reporting, and playback in the platform
  • Configurable alerts in Plaspy (movement, geofence, etc.) are triggered by reports the V55 delivers to the shared server

Common Configuration Workflow​

Follow this practical sequence when commissioning a V55 for Plaspy. Exact steps may differ slightly depending on the manufacturer tool or firmware your device uses.

  1. Access the official Reachfar configuration method or software appropriate for the V55 (manufacturer desktop tool, mobile app, or SMS command set).
  2. Enter the Plaspy server domain d.plaspy.com or alternatively enter the server IP 54.85.159.138 if the configuration tool requires an IP.
  3. Set the destination port to 8888 which Plaspy uses for all supported devices.
  4. Choose UDP or TCP as the transport type if the device requires a transport selection.
  5. Configure any required APN or cellular network settings so the device can reach Plaspy over the mobile data connection.
  6. Apply or save the configuration and, if the device requires it, restart the V55 to apply new network settings.
  7. Validate that the device reports to Plaspy by checking for initial position updates and status in your Plaspy account.

Example Configuration Commands​

The V55 may be configured using Reachfar tools or the vendor command set. Exact commands and syntax vary by firmware and vendor utility, and Reachfar provides the definitive command documentation. Because manufacturer commands and utilities differ across firmware versions, consult the V55 manual or Reachfar configuration guide for exact command strings and examples.

If you are using SMS or a manufacturer configuration tool, follow the official Reachfar examples for setting server, port, transport, and APN values. Preserve placeholders such as [apn] or similar as needed and substitute your operator APN, username, and password where applicable.

Configuration Notes​

  • Firmware differences matter: the exact menu names and command syntax depend on the V55 firmware revision and the configuration utility provided by Reachfar.
  • Transport choice UDP versus TCP can affect delivery characteristics; choose the transport recommended by your installer or by the Reachfar documentation, and note that Plaspy accepts either as long as the device targets the Plaspy endpoint and port.
  • Use the same Plaspy port 8888 for all devices to simplify firewall rules and platform ingestion consistency.
  • If you configure the device by SMS, keep a record of commands sent and responses received to aid troubleshooting.
  • Always cross check APN and network credentials with the mobile operator to ensure the V55 can reach d.plaspy.com or 54.85.159.138 from the installed location.

Why Use Plaspy with This Configuration​

Configuring the Reachfar V55 to report to Plaspy provides a straightforward path to real-time visibility, historical playback, and event-driven alerts for fleet and asset monitoring. The V55’s hybrid positioning and rugged design complement Plaspy’s centralized ingestion so operators can monitor devices across urban and remote environments.

To learn more about Plaspy and how the platform can support your fleet or asset workflows visit https://www.plaspy.com. For the latest device specific setup steps, command syntax, firmware notes, and installation instructions verify the V55 documentation on the Reachfar website at https://www.reachfargps.com/ as manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy