Skip to main content

STL - STL060 Configuration

This page covers the public configuration context for using the STL STL060 GPS tracker with Plaspy. It focuses on the practical server settings and preparation steps required to point the device at Plaspy so the device can report location and basic status information to the platform. Use this guide to understand what Plaspy expects and how to apply those settings using the device configuration method provided by the manufacturer.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools. The STL060 supports storing position data when GPRS is not available and includes SMS based settings and location requests, so you may use SMS for basic configuration in some environments or the manufacturer configuration tool for full server setup.

Configuration Overview​

The goal of configuration is to prepare the STL060 to communicate reliably with Plaspy and to validate that location reports are visible in the platform. This process focuses on supplying the correct Plaspy server endpoint, ensuring the device has an active communication path, and verifying reports arrive in Plaspy.

  • Point the tracker to the Plaspy server endpoint so location packets are routed to the platform
  • Configure the transport and port so the device can open a session to Plaspy
  • Verify the device has cellular connectivity or an appropriate communication path for live reporting
  • Use SMS configuration if a software tool is not available or as a fallback for validation
  • Confirm the device appears and reports in Plaspy after configuration

Plaspy Server Settings​

Use precisely these public Plaspy server settings when configuring the STL060 for Plaspy:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on device configuration options
  • Plaspy automatically detects the tracker protocol and all devices use the same port

Always enter either the server domain or IP and set the transport and port as shown above so the device sends data to Plaspy properly.

Typical Requirements Before Setup​

  • A powered and accessible STL060 device with the ability to accept configuration changes
  • A working SIM and data plan for GPRS based real time reporting if live tracking is required
  • The ability to send and receive SMS for SMS based settings and verification if you use SMS configuration
  • Access to the official manufacturer configuration method or software from the vendor
  • A reliable environment to test initial reports and validate visibility in Plaspy after configuration

How This Tracker Connects to Plaspy​

When configured for Plaspy the STL060 sends its position and any supported event messages to the shared Plaspy server endpoint and port. Plaspy receives these messages and maps them to the correct device profile by automatically detecting the tracker protocol.

  • Device sends location packets to d.plaspy.com or 54.85.159.138 on port 8888
  • Transport is either UDP or TCP depending on the device configuration choice
  • Plaspy automatically detects the tracker protocol and decodes incoming messages
  • Reports become visible in Plaspy for operational monitoring and history
  • If GPRS is unavailable the STL060 can retain data in memory and support SMS based requests for immediate position

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software provided by the vendor or installer.
  2. In the device server settings enter the Plaspy server domain d.plaspy.com or the server IP 54.85.159.138.
  3. Set the destination port to 8888 which is used by Plaspy for all supported devices.
  4. Choose UDP or TCP as the transport if the device requires a transport selection.
  5. Apply or save the configuration in the device interface or via SMS as supported.
  6. Restart the device if firmware or the tool recommends a reboot to apply network changes.
  7. Validate that the device reports to Plaspy by checking for incoming positions on the platform.

Example Configuration Commands​

The STL060 supports SMS based configuration and manufacturer tools, and exact command syntax can vary by firmware and release. Because manufacturer command formats and special parameters differ over time, follow the official device manual or configuration tool for exact commands. If you use SMS commands provided by the vendor, preserve any placeholders the manufacturer uses such as [apn], [apnu], or [apnp] when required, and replace them with your SIM APN details.

For SMS configuration the patterns may include sending a server command and a port command and then saving or rebooting. Use the official STL documentation for the exact text strings if SMS is your chosen method.

Configuration Notes​

  • Firmware versions can change command syntax and available features; confirm commands and behavior against the current STL documentation.
  • Choose UDP or TCP according to network conditions and your device firmware recommendations; Plaspy accepts both and detects the protocol automatically.
  • Use SMS based settings for remote or initial configuration when data connectivity is not yet available, then switch to GPRS for continuous reporting.
  • All devices in Plaspy use the same port 8888 which simplifies multi device deployment and server routing.
  • Testing a single device first and confirming visibility in Plaspy reduces troubleshooting scope for larger rollouts.

Why Use Plaspy with This Configuration​

Configuring the STL060 to report to Plaspy provides organizations with visibility into asset location and basic event reporting using a consistent server endpoint and port. Plaspy's automatic protocol detection reduces the need to select model specific protocol handlers during setup, letting you focus on network and device readiness.

Learn more about Plaspy and platform capabilities at https://www.plaspy.com. For the latest device specific setup details, firmware notes, SMS command syntax, and configuration tools refer to the manufacturer at http://siliconwireless.in because device configuration methods and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy