Skip to main content

Supermate - D10-T Configuration

This page covers the public configuration context for using the Supermate D10 T tracker with Plaspy. It collects the practical, nonproprietary setup information needed to point a D10 T at the Plaspy endpoint so the device can report location and event data into the Plaspy platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and the vendor configuration tool you use. Use this guide to understand the required Plaspy values and the typical workflow; always cross check manufacturer directions for device specific menus and commands.

Configuration Overview​

The goal of configuration is to prepare the D10 T so it communicates reliably with the Plaspy platform and becomes visible in your Plaspy account. The steps below are practical and focus on the core values that must be applied on the device or in the vendor configuration tool.

  • Set the device to report to the Plaspy server endpoint and confirm the transport method if required.
  • Ensure cellular connectivity and any required APN or network settings are in place so the tracker can reach the internet.
  • Validate that the device is sending data to the Plaspy server and that the platform is receiving and decoding messages.
  • Save and apply configuration, then reboot the tracker if the manufacturer recommends a restart to activate changes.
  • Confirm visibility in Plaspy by checking the device on the platform and reviewing recent location updates.

Plaspy Server Settings​

Apply these exact Plaspy server settings when configuring the Supermate D10 T:

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol

Plaspy uses the same port for all supported devices and will attempt to identify the tracker protocol automatically after the device connects.

Typical Requirements Before Setup​

  • Physical access to the Supermate D10 T to view serial number and to apply any menu or SMS configuration required by the manufacturer.
  • An active SIM card and a data plan compatible with the tracker if cellular networking is required; ensure the SIM is provisioned for internet access.
  • Access to the official Supermate configuration method or software from the manufacturer or vendor.
  • A charged battery or stable power so the tracker remains online during configuration and validation.
  • Your Plaspy account credentials and device registration details to confirm the tracker appears in the platform once it is reporting.

How This Tracker Connects to Plaspy​

The D10 T is configured to send its location and status updates to the shared Plaspy server endpoint and port. Plaspy then detects the incoming tracker protocol and decodes messages so the device appears in your Plaspy account.

  • The tracker sends periodic location reports and event messages to d.plaspy.com or to 54.85.159.138 on port 8888.
  • You can choose UDP or TCP on the device if the manufacturer requires an explicit transport selection.
  • Plaspy automatically detects the protocol used by the tracker once the first messages arrive.
  • After the server accepts connection, Plaspy processes reports so you can monitor locations, movement, and alerts in the platform.
  • Validation is done by confirming incoming messages on Plaspy and observing the device feed in your account.

Common Configuration Workflow​

  1. Access the official Supermate configuration method or software as provided by the manufacturer or vendor.
  2. In the device configuration settings, enter the Plaspy server address by using d.plaspy.com or the server IP 54.85.159.138.
  3. Set the server port to 8888.
  4. Choose UDP or TCP if the device configuration requires selecting a transport protocol.
  5. Enter any required network settings such as APN when prompted by the manufacturer tool, then apply or save the configuration.
  6. Restart the device if the manufacturer recommends a reboot to activate the new settings.
  7. Validate that the device reports to Plaspy by checking the device list and recent messages in your Plaspy account.

Example Configuration Commands​

The Supermate D10 T manufacturer commands and configuration interfaces vary by firmware and vendor tool. Because model specific command sets are not included here, follow the manufacturer documentation or configuration software for exact command text and syntax. If you have SMS or console commands from Supermate, apply the Plaspy server domain or IP and port 8888 in the same order the manufacturer prescribes.

If your vendor or firmware provides SMS commands, the typical pattern is:

  • Use the manufacturer command to set server domain or IP
  • Use the manufacturer command to set the port
  • Use the manufacturer command to set transport mode if required
  • Use the manufacturer command to save and reboot

Always preserve placeholder values exactly as provided by the manufacturer when substituting APN or credentials.

Configuration Notes​

  • Firmware differences can change exact menu names, SMS command syntax, and the location of server settings in vendor software; check the firmware release notes before applying settings.
  • Some firmware builds require entering either d.plaspy.com or the raw IP 54.85.159.138; both are provided here and either may be accepted by the device.
  • Choose UDP or TCP based on the device options; functionally Plaspy accepts both and will detect the protocol automatically.
  • When configuring remotely, ensure the tracker has a working SIM and network coverage so settings can be applied and validated.
  • Keep a record of serial numbers and configuration changes for installation tracking and future troubleshooting.

Why Use Plaspy with This Configuration​

Connecting the Supermate D10 T to Plaspy gives organizations continuous visibility into asset location and status using a single shared server configuration. The consistent Plaspy server values simplify deployment across many devices and help teams get trackers reporting quickly into the platform for monitoring and alerting.

To learn more about Plaspy and how the platform handles device connections and protocol detection visit https://www.plaspy.com. For the most current device specific commands, menus, and firmware details for the Supermate D10 T, verify manufacturer documentation at http://www.gps-summit.com/ since configuration methods and firmware behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy