Skip to main content

ThinkRace - VT07 Configuration

This page covers the public configuration context for using the ThinkRace VT07 tracker with the Plaspy platform. It summarizes the practical server settings and example setup commands that are publicly available and useful when preparing the VT07 to report to Plaspy for tracking and monitoring.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol so you do not need to choose a Plaspy protocol by device. Exact manufacturer-side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools; this guide focuses on the practical public settings and SMS commands commonly used with the VT07.

Configuration Overview​

The configuration process prepares the VT07 to communicate with Plaspy, validates connectivity over the mobile network, and enables visibility of location and alarms in the Plaspy platform. Where available, SMS-based configuration commands are a common way to apply the settings listed here.

  • Configure the device to use Plaspy as its reporting endpoint so position and event messages are sent to the platform.
  • Set operator APN and GPRS server information so the VT07 can establish data connectivity.
  • Choose UDP or TCP transport as the VT07 requires, matching Plaspy support.
  • Validate the device reports successfully to Plaspy and check live visibility in the platform.
  • Use manufacturer tools or SMS commands provided by ThinkRace for device-specific configuration when applicable.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP — the device may be configured using either UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol and uses the same port for all supported devices

Typical Requirements Before Setup​

  • A powered VT07 unit with access to the device SMS or configuration interface as provided by ThinkRace
  • An active SIM card installed and able to use GPRS data on the operator network with the correct APN
  • Operator APN, APN username, and APN password if required by the mobile operator
  • Access to the ThinkRace user manual or vendor configuration tool for device-specific commands
  • Basic ability to send SMS commands from a phone or to use the ThinkRace configuration utility
  • A Plaspy account or instructions from your Plaspy administrator to confirm device visibility after configuration

How This Tracker Connects to Plaspy​

The VT07 is configured to send its location and event data to Plaspy by pointing the device at the shared Plaspy server endpoint and port. Once the IP or domain and port are set and the device has GPRS connectivity, Plaspy receives and interprets messages automatically.

  • The tracker reports location updates and alarm events to the configured Plaspy endpoint
  • Data is sent to d.plaspy.com or directly to 54.85.159.138 on port 8888
  • Transport can be UDP or TCP depending on the device setting; Plaspy accepts both
  • Plaspy automatically detects the tracker protocol so no protocol selection is required on the platform side
  • After a successful connection the device becomes visible and sends periodic updates to Plaspy

Common Configuration Workflow​

  1. Access the official ThinkRace configuration method documented by the manufacturer, for example SMS configuration or the vendor software.
  2. Enter the Plaspy server address using d.plaspy.com or the IP 54.85.159.138 as instructed by the device manual.
  3. Set the port to 8888 (Plaspy uses the same port for all devices).
  4. Choose UDP or TCP on the device if a transport option is requested.
  5. Set the operator APN and any APN credentials required so the VT07 can establish GPRS data connectivity.
  6. Apply or save the configuration on the device and restart the tracker if the device requires a reboot for new settings to take effect.
  7. Validate the device reports to Plaspy by checking device visibility and recent position updates in the platform.

Example Configuration Commands​

The ThinkRace VT07 supports SMS-based configuration. Below are the public example commands commonly used to prepare the device for reporting to Plaspy. Preserve placeholders when replacing with your operator values.

  • Factory reset (optional initial step)
clear
  • Set the operator APN
APN,[apn]

If your operator requires username and password, use the extended form:

APN,[apn],[apnu],[apnp]
  • Set the GPRS server to Plaspy by IP and port
IP1,54.85.159.138,8888
  • Set the update interval to 60 seconds
ITV,60
  • Check current settings (verification)
C

Notes on placeholders:

  • [apn] is the mobile operator APN
  • [apnu] is the APN username if required
  • [apnp] is the APN password if required

Send each command as an individual SMS from the device administrator phone number as described in ThinkRace documentation. Apply the factory reset only when needed or as part of an initial clean setup.

Configuration Notes​

  • SMS-based configuration is supported by the public ThinkRace VT07 commands shown above; manufacturer tools or direct configuration utilities may also be available.
  • Firmware and hardware revisions may change command behavior or available settings; always confirm the command syntax against the latest ThinkRace documentation.
  • Choose UDP or TCP according to installer preference; Plaspy accepts both and will auto detect the protocol used by the tracker.
  • Plaspy uses port 8888 for all supported devices; do not change the port when aiming to connect to Plaspy.
  • Ensure APN credentials are accurate for the SIM and operator region so GPRS connectivity can be established.

Why Use Plaspy with This Configuration​

Configuring the VT07 to report to Plaspy provides a straightforward path to vehicle visibility, alarm monitoring, and operational oversight. Using the shared Plaspy endpoint and port simplifies deployment across fleets because the platform automatically detects the tracker protocol and accepts standard device messages once the server and APN settings are correct.

To learn more about Plaspy and how Plaspy handles device connectivity and fleet monitoring visit https://www.plaspy.com. For the most current device specific commands, firmware notes, and official configuration procedures verify details at the ThinkRace website https://www.thinkrace.com/ because manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy