Skip to main content

ThinkRace - VT200 Configuration

This page covers the public configuration context for using the ThinkRace VT200 OBD tracker with the Plaspy platform. It collects the practical, public-facing settings and workflows you will use to point a VT200 to Plaspy and validate that the device is reporting correctly. Use this as a concise reference for the server settings and the common setup steps; manufacturer documentation remains the definitive source for device specific details.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware revision, hardware revision, installation type, and vendor configuration tools. The VT200 supports SMS and GPRS based configuration commands in its public documentation, and the examples below show the command format commonly used to set APN and server parameters when preparing the device for Plaspy.

Configuration Overview​

Configuring a VT200 for Plaspy means preparing the device so it can open a data channel to Plaspy's server, authenticate on the mobile network, and begin reporting GPS and event data to the platform. The process typically combines setting a network APN, configuring the GPRS server address and port, and verifying that the tracker appears in Plaspy.

  • Set the mobile operator APN on the VT200 so the device can establish GPRS data.
  • Configure the VT200 to send data to Plaspy using the shared server endpoint and port.
  • Choose the transport protocol (UDP or TCP) on devices that require a transport selection.
  • Apply settings and restart or reinitialize the tracker so changes take effect.
  • Confirm the tracker is visible and reporting as expected in Plaspy after configuration.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on device configuration option
  • Plaspy automatically detects the tracker protocol and all devices use the same port in Plaspy

Typical Requirements Before Setup​

  • Power the VT200 and ensure the OBD connection or installation provides stable device power.
  • A working cellular SIM card with a data plan and the correct APN for the operator.
  • Ability to send SMS commands to the device or use the official ThinkRace configuration tool if available.
  • Access to the VT200 default device password for SMS configuration if required (public examples show 888888 as the default).
  • The Plaspy server values d.plaspy.com or 54.85.159.138 and port 8888 to enter in the tracker configuration.

How This Tracker Connects to Plaspy​

The VT200 is configured to report location and status by opening a GPRS connection to Plaspy's shared server endpoint and port. After the APN and server are set, the tracker will push location and event messages to Plaspy where the device becomes visible in the platform and can be monitored.

  • The device uses the configured APN to connect to the mobile data network.
  • VT200 sends its tracking packets to the Plaspy server at d.plaspy.com or 54.85.159.138 on port 8888.
  • Plaspy automatically detects the incoming tracker protocol and parses messages accordingly.
  • Transport may be UDP or TCP as allowed by the device configuration.
  • Once reporting, position, movement, and status events are visible in Plaspy for operational monitoring.

Common Configuration Workflow​

  1. Access the official ThinkRace configuration method for the VT200, such as SMS commands or the manufacturer tool recommended in the VT200 documentation.
  2. Ensure the device has a working SIM and that you know the operator APN for the SIM.
  3. Enter d.plaspy.com or 54.85.159.138 as the device server address in the device configuration.
  4. Set the server port to 8888 as required by Plaspy.
  5. Choose UDP or TCP transport if the VT200 requires a transport selection.
  6. Apply or save the configuration on the device and restart the tracker if the device requires a reboot to apply settings.
  7. Validate that the VT200 is reporting by checking device visibility and incoming data in Plaspy.

Example Configuration Commands​

The VT200 supports SMS based configuration. The public example commands below use the device SMS command format. The sample device password in public documentation is 888888 and is used in the examples. Replace placeholders where noted.

  • Set the operator APN
(Set,888888,apn,[apn],[apnu],[apnp])

Explanation: Replace [apn] with your mobile operator APN. If your operator requires a username or password include [apnu] and [apnp] respectively. If no username or password are required, you may omit those placeholders according to the device SMS format.

  • Set the GPRS server to Plaspy by IP and port
(Set,888888,server,54.85.159.138,8888)

Explanation: This command sets the VT200 to report to Plaspy using the server IP and port shown. You can alternatively use d.plaspy.com where your device SMS workflow or manufacturer tool accepts a domain name, but the example command above is the public SMS form provided.

Notes on use:

  • Send these SMS messages from a trusted phone number as specified in the VT200 documentation.
  • Keep the order: set APN first, then set server, then restart or reinitialize the tracker if required.

Configuration Notes​

  • The VT200 public configuration supports SMS based commands for APN and server configuration as shown above.
  • Firmware revisions or regional firmware variants may change accepted SMS command syntax or default password behavior; confirm with ThinkRace documentation for your device version.
  • Choose UDP or TCP based on the device option and any network considerations; Plaspy accepts either and will auto detect the protocol.
  • All devices in Plaspy use the same port and Plaspy automatically detects the tracker protocol, so use port 8888 when configuring the VT200 for Plaspy.
  • If you use manufacturer software or an authorized installer tool, follow the official tool workflow and apply the Plaspy server settings as part of the setup.

Why Use Plaspy with This Configuration​

Using the ThinkRace VT200 with Plaspy provides a straightforward way to add OBD vehicle tracking into a centralized fleet monitoring platform. When the VT200 is configured with the Plaspy server settings and proper APN, organizations gain near real time visibility into vehicle location and status, enabling operational oversight and easier fleet management.

To learn more about Plaspy and supported integrations visit https://www.plaspy.com. For the most current device specific instructions, firmware notes, and command reference verify details on the manufacturer website https://www.thinkrace.com/. Manufacturer specifications and setup methods can change over time, so always confirm the latest information before deploying devices at scale.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy