Skip to main content

TK-Star - LK208 Configuration

This page covers the public configuration context for using the TK-Star LK208 portable GPS tracker with Plaspy. It summarizes the practical, publicly available steps and SMS command examples commonly used to point an LK208 to Plaspy so the device can report location and status to the platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while manufacturer-side setup steps can vary by firmware revision, installation type, and vendor tools. The examples below are drawn from publicly shared LK208 SMS setup commands and the standard Plaspy endpoint information to help you prepare the device for use with Plaspy.

Configuration Overview​

Preparing the LK208 for Plaspy integration focuses on setting the network parameters, enabling GPRS reporting, and validating that the device reaches the Plaspy server. The typical LK208 setup uses SMS commands to configure APN and server details, then switches the unit into GPRS reporting mode.

  • Set the cellular APN, and optionally APN username and password, so the tracker can use mobile data.
  • Configure the GPRS server address to the Plaspy endpoint so the device will send telemetry to the platform.
  • Choose transport (UDP or TCP) and the shared Plaspy port so packets arrive correctly on the platform.
  • Enable upload interval suitable for your use case to control reporting frequency.
  • Verify connectivity and that the device appears in Plaspy after configuration.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol and all devices in Plaspy use the same port

Typical Requirements Before Setup​

  • A charged and operational LK208 unit with access to SMS configuration or the manufacturer configuration tool.
  • An active SIM card with data enabled and a correct APN for the mobile operator.
  • Ability to send SMS messages to the tracker for SMS based configuration, if you use SMS commands.
  • Reference to the LK208 manufacturer documentation or configuration guide for firmware specific instructions.
  • Basic knowledge of the device password used in configuration SMS commands (the public default used in examples is 123456).
  • A plan for an appropriate upload interval based on battery life and tracking needs.

How This Tracker Connects to Plaspy​

When configured for Plaspy, the LK208 is directed to the shared Plaspy server endpoint and uses the common platform port so the platform can receive and interpret its messages. Plaspy then places the tracker on your account using automatic protocol detection to map protocol messages to the platform.

  • The tracker sends GPRS data to the Plaspy server endpoint at d.plaspy.com or 54.85.159.138 on port 8888.
  • The device can use either UDP or TCP transport depending on tracker firmware or configuration choice.
  • Plaspy automatically detects the tracker protocol and decodes incoming messages.
  • After successful connection, the device becomes visible in Plaspy and reports its location and status at the configured upload interval.
  • Validation on the platform confirms the device is reporting and that telemetry appears as expected.

Common Configuration Workflow​

  1. Access the official TK-Star configuration method for the LK208 such as SMS commands or the vendor configuration tool described in the manufacturer documentation.
  2. Enter the Plaspy server endpoint either as domain d.plaspy.com or by IP 54.85.159.138 depending on the device interface.
  3. Set the server port to 8888 exactly as required by Plaspy.
  4. Choose UDP or TCP transport if the device requires an explicit transport selection.
  5. Configure APN settings for the SIM so the tracker can use mobile data, including optional APN username and password if required.
  6. Apply or save the configuration, then restart or reboot the device if the manufacturer instructions require it.
  7. Validate that the device reports to Plaspy by checking the device list and recent position updates on the Plaspy platform.

Example Configuration Commands​

The following SMS commands are public examples for configuring an LK208. These commands assume the tracker uses the default device password 123456. Send each command as a separate SMS to the device number. Preserve the password and replace placeholders where indicated.

  • Restore factory settings (optional initial step)
begin123456
  • Set the operator APN (replace [apn] with your mobile operator APN)
apn123456 [apn]
  • Set the APN username (use only if your operator requires a username; replace [apnu] with the APN username)
apnuser123456 [apnu]
  • Set the APN password (use only if your operator requires a password; replace [apnp] with the APN password)
apnpasswd123456 [apnp]
  • Set the GPRS server to Plaspy by IP and port (Plaspy uses this IP and port)
adminip123456 54.85.159.138 8888
  • Set the upload interval to 60 seconds (adjust the interval to suit your needs)
upload123456 60
  • Switch the device to GPRS mode so it sends data to the configured server
gprs123456

Placeholders explanation:

  • [apn] — mobile operator APN string required for data access.
  • [apnu] — APN username if required by the operator.
  • [apnp] — APN password if required by the operator.

Note: The default password in these public examples is 123456. If your device password has been changed, use the correct password in each command.

Configuration Notes​

  • SMS based configuration is a common public method for TK-Star devices; verify whether your LK208 unit uses SMS commands or a vendor tool for configuration.
  • Firmware versions and hardware revisions can change command syntax and behavior; always cross check with the LK208 manufacturer documentation.
  • When given a choice, TCP vs UDP can affect delivery semantics; choose the transport that matches your deployment and any network restrictions.
  • Plaspy uses a single shared port for all supported devices and automatically detects the tracker protocol, so use port 8888 for this device.
  • Market versions of the LK208 may differ by region or vendor customization; verify settings such as APN requirements with the SIM operator.

Why Use Plaspy with This Configuration​

Using the TK-Star LK208 configured to report to Plaspy provides a straightforward path to real time visibility and centralized monitoring. Pointing the device to the Plaspy server endpoint and port allows organizations to consolidate tracking data for vehicles, equipment, and cargo into a single platform for event alerts, location history, and operational oversight.

To learn more about Plaspy and platform capabilities visit https://www.plaspy.com. For the most current device specific configuration details, firmware notes, and manufacturer guidance verify the latest information on the TK Star website at https://www.tk-star.com/ since setup methods and device behavior can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy