Skip to main content

TopFly - T8808 Configuration

This page covers the public configuration context for using the TopFly T8808 tracker with Plaspy. It summarizes the practical server settings and the common setup workflow used to point a T8808 device to the Plaspy backend, and it includes the publicly available SMS commands used for initial device configuration when applicable.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, but exact manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. The T8808 supports SMS based configuration as shown in the public commands below; use this page as a practical starting point and verify exact command formats against TopFly documentation or firmware release notes.

Configuration Overview​

The goal of configuration is to prepare the T8808 so it can reliably communicate with Plaspy and be visible in the platform for tracking and monitoring. For T8808 devices this typically includes setting the correct APN for GPRS, pointing the device to the Plaspy server endpoint and port, and configuring reporting intervals so location data is sent at the required cadence.

  • Configure the device APN and credentials so the tracker has GPRS connectivity
  • Point the tracker to the Plaspy server endpoint so data reaches d.plaspy.com
  • Set the reporting interval and timezone so location updates match your needs
  • Validate device connectivity and verify the tracker appears in Plaspy
  • Use SMS or the official TopFly configuration tools depending on installer preference

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol so devices can use either UDP or TCP

These server details are the public Plaspy settings to use when configuring any compatible tracker for the platform. Plaspy uses the same port for all supported devices and performs automatic protocol detection.

Typical Requirements Before Setup​

  • A charged and installed TopFly T8808 device with a working SIM card and GPRS service enabled
  • Access to the device phone number or the vehicle where the device is installed for SMS based configuration
  • APN name and, if required, APN username and APN password for the mobile operator
  • Knowledge of the device configuration method provided by the manufacturer such as SMS commands or official configuration software
  • Basic confirmation that the device firmware supports the public SMS command set used for configuration

How This Tracker Connects to Plaspy​

The T8808 is prepared to send location and event data to the shared Plaspy server endpoint and port so it can be displayed and managed in the Plaspy platform. Once configured with correct APN and server settings, the device will initiate a GPRS connection and start reporting on the chosen transport protocol.

  • The tracker connects to the Plaspy server endpoint d.plaspy.com or to the IP address 54.85.159.138 on port 8888
  • Transport can be configured as UDP or TCP depending on device settings and installer preference
  • Plaspy receives and processes incoming packets and automatically detects the device protocol
  • Location updates and alarms are forwarded to the Plaspy platform for visibility and alerting
  • Reporting interval configuration determines how frequently position updates are sent to Plaspy

Common Configuration Workflow​

  1. Access the official TopFly configuration method such as SMS commands or the manufacturer tool described in the device documentation.
  2. Enter d.plaspy.com or the alternative server IP 54.85.159.138 in the device server settings.
  3. Set the server port to 8888 as required by Plaspy.
  4. If the device requires a transport selection, choose UDP or TCP according to your network and installation needs.
  5. Configure APN and any required APN username or password so the device has mobile data connectivity.
  6. Apply or save the configuration and restart the device if the device or firmware requires a reboot for changes to take effect.
  7. Validate that the device reports to Plaspy and appears in the platform with expected location updates.

Example Configuration Commands​

The TopFly T8808 public configuration commands are commonly sent by SMS to the device phone number. The sample commands below use the device default password 0000 as provided in public TopFly instructions. Keep the order when performing initial setup so APN and server are set before enabling regular reporting.

  • Set the time zone to UTC 0
GMT,0000,0#
  • Set the operator APN. Replace placeholders with your operator values:
    • [apn] = APN name for your mobile operator
    • [apnu] = APN username if required (keep empty if not used)
    • [apnp] = APN password if required (keep empty if not used)
APN,0000,[apn],[apnu],[apnp]#
  • Set the GPRS server using the Plaspy server IP and port
IP,0000,54.85.159.138 8888#
  • Set the reporting interval to 60 seconds
TIMER,0000,60:60:0:0#

Notes on these commands:

  • The default device password used in these examples is 0000. If you have changed the device password, replace 0000 with your device password.
  • Preserve the placeholders [apn], [apnu], and [apnp] when preparing SMS templates and replace them with your live operator credentials.
  • Some installers prefer to use a domain name instead of IP if the device firmware supports it; if using a domain, follow TopFly instructions for domain syntax.

Configuration Notes​

  • Firmware and hardware revisions can affect command formats and supported parameters; always confirm with TopFly documentation for your device firmware version.
  • The T8808 supports SMS based configuration in public documentation; use SMS only from a trusted phone number and record any password changes.
  • Choose UDP or TCP based on your network conditions and any guidance from your connectivity provider; Plaspy will auto detect the protocol used by the device.
  • Because Plaspy uses the same port 8888 for all supported devices, ensure this port is not blocked by your network.
  • If configuration changes do not take effect immediately, try restarting the device or re-sending the commands in the order shown above.

Why Use Plaspy with This Configuration​

Using the TopFly T8808 with Plaspy provides a straightforward path to get vehicle location and event data into a unified fleet management platform. With the shared Plaspy endpoint and automatic protocol detection, installers can rely on consistent server settings while focusing on correct APN and device setup.

To learn more about Plaspy and the platform features, visit https://www.plaspy.com. For the latest device specific configuration details, firmware notes, and manufacturer guidance for the TopFly T8808, verify current information at https://www.topflytech.com/ since manufacturer specifications and setup methods can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy