Skip to main content

TopTen - GT08S Configuration

This page documents the public configuration context for using the TopTen GT08S tracker with Plaspy. It focuses on the practical server settings, the manufacturer provided SMS commands from public configuration notes, and the minimal steps required to prepare the tracker so it can communicate with Plaspy for real time visibility.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol. Manufacturer side setup steps can vary by firmware, hardware revision, installation type, and vendor tools. The GT08S supports SMS and GPRS configuration in published materials, and the commands shown here reflect publicly available configuration commands for the model.

Configuration Overview​

The configuration process prepares the GT08S so it reports location and status to Plaspy and becomes visible in the platform. The public GT08S configuration flow concentrates on setting the network APN and the GPRS server endpoint and validating the tracker identifier used by Plaspy.

  • Configure the tracker APN and GPRS server so the device can reach the internet and Plaspy servers
  • Ensure the device identifier is recognized by the platform using the IMEI derived tracker ID shown in the PAR response
  • Choose transport and set the shared Plaspy port so messages are delivered to Plaspy
  • Validate connectivity and confirm the tracker is reporting to Plaspy
  • Optionally restore factory settings or verify current parameters before deployment

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP depending on device preference
  • Plaspy automatically detects the tracker protocol so all devices may use the same port and Plaspy will interpret the protocol correctly

Typical Requirements Before Setup​

  • A powered GT08S device with access to the manufacturer configuration method or SMS control channel
  • An active SIM card with data enabled and correct APN credentials for the mobile network
  • The device IMEI available for identification and platform registration
  • Access to send and receive SMS to the device if using SMS based configuration
  • Basic familiarity with the tracker SMS command format and placeholders for APN parameters

How This Tracker Connects to Plaspy​

The GT08S is configured to send location and device data to the shared Plaspy endpoint and port over the mobile network. Plaspy receives incoming TCP or UDP messages on the common port and applies automatic protocol detection so the platform can accept a variety of tracker protocols without per device port changes.

  • The GT08S is pointed at the Plaspy server endpoint using the server domain or IP
  • The tracker uses the shared Plaspy port 8888 for all supported devices
  • Transport can be set to UDP or TCP on the tracker depending on preference and firmware support
  • The device identifier used by Plaspy corresponds to the last 14 digits of the IMEI as returned in the PAR response
  • Plaspy will auto detect the tracker protocol once traffic is received on the shared port

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or software, or prepare to send SMS commands as documented by TopTen
  2. Enter the Plaspy server by domain d.plaspy.com or by IP 54.85.159.138 in the device server settings
  3. Set the server port to 8888 which Plaspy uses for all supported devices
  4. Choose UDP or TCP as the transport if the device requires a transport selection
  5. Provide APN settings using the appropriate placeholders or values for your mobile network
  6. Apply or save the configuration and restart the GT08S if required by the device
  7. Validate that the device reports to Plaspy and confirm the tracker ID matches the last 14 digits of the IMEI in the PAR response

Example Configuration Commands​

The GT08S public configuration notes include SMS commands to restore defaults, set the APN and server, and verify settings. Commands are sent as SMS to the tracker using the device SMS password prefix. Preserve placeholders when replacing with your actual network values.

  • Optional initial factory reset command labeled as an optional step when needed
111111CLR
  • Set APN and GPRS server to point to Plaspy using IP and port and include APN placeholders
111111WWW:IPN:54.85.159.138;COM:8888;APN:[apn],[apnu],[apnp];RPT:60;SLP:60;RUN:2;

Notes about the placeholders

  • [apn] is the mobile network APN name

  • [apnu] is the APN username if required by the carrier

  • [apnp] is the APN password if required by the carrier

  • Verification command to request current WWW settings from the tracker

111111WWW:

Public configuration guidance also states that the tracker ID used in Plaspy corresponds to the last 14 digits of the IMEI as returned in the PAR command or PAR response. Use the manufacturer's method to view the PAR response to confirm the IMEI and derived tracker ID.

Configuration Notes​

  • SMS based configuration is supported in the public GT08S materials so you may configure the device without a dedicated PC tool if SMS is available
  • Firmware revisions and hardware variants can change command syntax or available parameters; verify commands against the device firmware release
  • Where the device offers a choice between UDP and TCP select the transport best suited for your network and then confirm delivery to Plaspy on port 8888
  • Keep APN credentials and SMS password information private and only use official carrier values for APN fields
  • Plaspy uses the same port for all supported devices and automatically detects the tracker protocol after the first successful connection

Why Use Plaspy with This Configuration​

Using the GT08S with Plaspy gives teams a practical way to centralize location reporting and operational monitoring across vehicles. By pointing the GT08S to the shared Plaspy endpoint and applying the public SMS commands above, organizations can confirm device connectivity, ingest position reports, and manage device visibility in one platform.

To learn more about Plaspy visit https://www.plaspy.com. Manufacturer specifications and setup steps can change over time so verify device specific configuration methods, firmware behavior, and command syntax with the official TopTen site at http://www.t10.cn before final deployment.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy