Skip to main content

TrackerKing - DK12 Configuration

This page describes the public configuration context for using the TrackerKing DK12 with Plaspy. It focuses on the practical server settings and workflow required to point a DK12 at Plaspy and validate that the tracker communicates correctly with the platform. Use this guide alongside the device manual when applying settings or performing an installation.

Plaspy uses shared server settings across supported devices and automatically detects tracker protocols, so DK12 installations typically require the same server endpoint and port used by other devices. Exact manufacturer side steps can vary by firmware, hardware revision, installation type, and vendor configuration tools. The DK12's 4G Cat1 connectivity with 2G fallback and its vehicle features such as ACC detection and immobilizer support are relevant when planning the installation and validation workflow.

Configuration Overview​

This configuration prepares the DK12 to report location and telemetry to Plaspy and ensures the device is visible and manageable in the platform. The steps below emphasize practical actions an installer or integrator will take to enable reliable communication between the tracker and Plaspy.

  • Point the DK12 to the Plaspy ingestion endpoint so position and alarm messages reach the platform.
  • Select the transport mode supported by the device and match Plaspy settings for reliable delivery.
  • Validate live reporting and alarm events so the DK12 appears in Plaspy mapping and alert rules.
  • Confirm that ignition and immobilizer signals are received if those features are used for alerts or remote actions.
  • Verify device power and network connectivity to avoid intermittent reporting or blind areas.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol and all devices in Plaspy use the same port 8888

Use either the domain d.plaspy.com or the IP 54.85.159.138 when configuring the DK12. Port 8888 is used for every device in Plaspy and the platform will detect the protocol sent by the tracker automatically.

Typical Requirements Before Setup​

  • Device powered and wired according to the TrackerKing DK12 installation instructions.
  • Active mobile data SIM provisioned for 4G Cat1 with fallback to 2G where required by coverage.
  • Access to the official TrackerKing configuration method such as the vendor tool, SMS commands, or web interface supported by the DK12.
  • Knowledge of whether the DK12 variant in use requires TCP or UDP selection for transport.
  • Physical access to the tracker for restart and validation during commissioning.
  • A Plaspy account and project where new devices will be observed after reporting.

How This Tracker Connects to Plaspy​

The DK12 is configured to send position fixes, alarms, and telemetry to the shared Plaspy server endpoint and port so those messages are ingested into the Plaspy platform for real time monitoring and historical playback. Plaspy supports common tracker protocols compatible with the DK12 so integration is typically a matter of pointing the device at the Plaspy endpoint and confirming connectivity.

  • The tracker sends periodic GPS position messages to d.plaspy.com or 54.85.159.138 on port 8888.
  • Alarms such as vibration, geo-fence, overspeed, and immobilizer events are forwarded to Plaspy for alerting.
  • Ignition status and virtual ignition reporting are delivered to Plaspy to support session logs and rule triggers.
  • Plaspy detects the tracker protocol automatically so no protocol selection is required in the platform.
  • Reporting, route history, and telemetry data become visible in Plaspy once the device successfully reports to port 8888.

Common Configuration Workflow​

  1. Access the official TrackerKing configuration method provided for the DK12 such as the vendor configuration tool, SMS command set, or the installer interface described in the device manual.
  2. Enter the Plaspy server address using either d.plaspy.com or 54.85.159.138 in the device server host field.
  3. Set the server port to 8888. Remember that Plaspy uses the same port for all supported devices.
  4. Choose UDP or TCP if the DK12 firmware requires an explicit transport selection for data reporting.
  5. Apply or save the configuration in the TrackerKing tool or via SMS commands and confirm the device accepted the new settings.
  6. Restart the DK12 if required by the device firmware or installer guidance to ensure the new server settings take effect.
  7. Validate that the DK12 reports to Plaspy by checking device appearance and recent telemetry in the Plaspy dashboard or monitoring tools.

Example Configuration Commands​

The DK12 may be configured using TrackerKing vendor tools, direct SMS commands, or a configuration interface depending on the firmware and installer method. Exact command formats and tools vary by firmware version and vendor release, so follow the official TrackerKing manual for the correct command set for your DK12 variant. Plaspy requires the server endpoint to be set to d.plaspy.com or 54.85.159.138 and the port to be 8888 with either UDP or TCP as the transport if the device needs a selection.

Configuration Notes​

  • Firmware differences across DK12 hardware revisions can change command syntax and configuration options; always check the device firmware version before applying instructions.
  • Choose UDP or TCP based on network characteristics and the DK12 firmware behavior; UDP may be more tolerant on mobile networks while TCP offers connection confirmation when supported.
  • When using vendor SMS configuration, ensure placeholders such as APN values are populated correctly according to the operator and hardware variant.
  • Because Plaspy uses port 8888 for all devices and automatically detects protocols, the platform side requires no per device port changes.
  • If the DK12 supports multiple tracker protocols like GT06, JT808, or Tianqin, protocol selection is generally automatic on the Plaspy side but confirm the device is sending a compatible message format.

Why Use Plaspy with This Configuration​

Using the TrackerKing DK12 with Plaspy gives organizations a dependable path to real time location, trip history, and alarm handling without custom protocol work. The DK12's multi band connectivity and vehicle aware inputs pair with Plaspy's ingestion and alerting to provide live monitoring, theft mitigation tools, and historical route playback for fleet and asset management workflows.

To learn more about Plaspy and platform capabilities visit https://www.plaspy.com and review the latest device specific information and firmware notes on the TrackerKing site https://trackerking.cn/. Manufacturer specifications and setup methods can change over time so verify the current DK12 configuration details on the TrackerKing website when planning an installation.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy