Skip to main content

Tytan SAT - DS520B Configuration

This page documents the public configuration context for using the Tytan SAT DS520B tracker with Plaspy. It focuses on the shared Plaspy server settings and the practical steps required to point a DS520B at Plaspy so the device can deliver real time location and telemetry to the platform. The DS520B is a GSM/GPRS tracker with analog and digital I O, digital outputs, 1‑wire temperature support, and non volatile buffering, all of which are commonly forwarded to fleet platforms like Plaspy.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device reports in. Exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools, so this page describes the public Plaspy configuration values and a practical workflow to apply them to the DS520B while encouraging verification against manufacturer instructions.

Configuration Overview​

Configuring the DS520B for Plaspy prepares the device to send location, sensor, and I O events to the platform so assets appear in dashboards, alerts are triggered, and historical reporting is recorded. This process is primarily about setting the device server endpoint, validating the cellular link, and confirming that Plaspy receives regular reports from the tracker.

  • Point the DS520B to the Plaspy server endpoint so telemetry is delivered to the platform.
  • Choose the appropriate transport option on the device (UDP or TCP) if the firmware requires it.
  • Ensure the device has a working GSM GPRS connection and any required SIM provisioning.
  • Verify device I O and sensor wiring so telemetry values are meaningful when ingested by Plaspy.
  • Confirm the device appears in Plaspy and sends periodic position and event updates.

Plaspy Server Settings​

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888
  • Transport: the DS520B may be configured to use UDP or TCP on port 8888
  • Protocol handling: Plaspy automatically detects the tracker protocol when the device connects

Note: Plaspy uses the same port number for all supported devices and relies on automatic protocol detection to handle different tracker formats.

Typical Requirements Before Setup​

  • A powered and accessible DS520B unit installed according to the manufacturer instructions.
  • A provisioned cellular SIM with data enabled for GSM GPRS communications where required.
  • Access to the official Tytan SAT configuration tool, SMS commands, or provisioning software provided by the vendor.
  • Knowledge of any required APN and operator credentials for cellular data if the device needs them.
  • Physical or remote access to device wiring for sensors and I O to verify inputs and outputs.
  • An account on Plaspy and the ability to view incoming devices on the platform for validation.

How This Tracker Connects to Plaspy​

When configured, the DS520B sends location and telemetry over GSM GPRS to the Plaspy server endpoint and port so the platform can ingest data for real time tracking, alerts, and historical analysis. Plaspy receives the device traffic on the shared endpoint and automatically determines the protocol in use.

  • The device reports position and movement data to d.plaspy.com or directly to 54.85.159.138 on port 8888.
  • Telemetry such as digital and analog input states and 1‑wire temperature readings are transmitted to Plaspy for dashboarding and rules.
  • Digital outputs and remote control actions can be invoked from Plaspy when configured and wired correctly.
  • Non volatile buffering on the DS520B preserves events during outages and forwards them to Plaspy when the connection is restored.
  • Plaspy’s automatic protocol detection eliminates the need to select a specific protocol in the platform for supported tracker models.

Common Configuration Workflow​

  1. Access the official Tytan SAT configuration method or software provided by the vendor (manufacturer tool, SMS commands, or provisioning interface).
  2. Enter the Plaspy server as either the domain d.plaspy.com or the server IP 54.85.159.138 depending on the device configuration options.
  3. Set the device port to 8888 as the destination port for telemetry.
  4. Choose UDP or TCP as the transport option if the DS520B firmware requires a transport selection.
  5. Apply or save the configuration in the device interface or send the required SMS provisioning commands.
  6. Restart the device if the manufacturer instructions require a reboot for settings to take effect.
  7. Validate that the device reports to Plaspy by checking that the tracker appears in your Plaspy account and sends expected position and telemetry updates.

Example Configuration Commands​

This model configuration does not include public command strings in this guide. Exact provisioning commands and the syntax used to set server, port, transport, APN, and other parameters depend on the Tytan SAT firmware and the vendor's configuration tool. When using SMS or a manufacturer utility to configure the DS520B, ensure the server is set to d.plaspy.com or 54.85.159.138 and the port is set to 8888, and choose UDP or TCP if required by the device. Consult the Tytan SAT documentation or vendor software for the exact command formats.

Configuration Notes​

  • Firmware differences can change the exact menu names, SMS command syntax, or provisioning workflow; always check the device firmware version before applying instructions.
  • Choose UDP or TCP based on installation requirements; UDP is commonly used for lightweight telemetry while TCP provides connection confirmation where supported by the device firmware.
  • Because Plaspy uses the same port for all devices and performs automatic protocol detection, you only need to point the DS520B at d.plaspy.com or 54.85.159.138 and set port 8888 in most cases.
  • Installer best practice is to verify I O wiring and sensor calibration on the vehicle before finalizing deployment to ensure meaningful telemetry arrives in Plaspy.
  • Market variations and hardware revisions may alter available features or command sets; manufacturer documentation is the authoritative source for device specific commands.

Why Use Plaspy with This Configuration​

Using the DS520B with Plaspy provides a practical path to real time vehicle and cargo visibility, integrating location, sensor telemetry, and event reporting into a single platform for operations and security teams. The DS520B’s I O options, temperature sensor support, remote outputs, and local buffering complement Plaspy’s dashboards and rule engine to deliver actionable insights for fleet management and anti theft workflows.

To learn more about Plaspy visit https://www.plaspy.com. Device specific configuration methods, firmware behavior, and manufacturer details can change over time, so verify the latest setup and command references on the official Tytan SAT website http://tytansat.com/.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy