Skip to main content

Ulbotech - T356 Configuration

This page documents the public configuration context for using the Ulbotech T356 with Plaspy. It focuses on the shared server settings and practical steps required to point the device at the Plaspy ingestion endpoint so that the tracker can upload stored and live telemetry. Use this guide to understand what to prepare before integrating a T356 into a Plaspy account.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer side setup steps can vary by firmware revision, hardware variation, installation type, or vendor configuration tools, so verify device-specific menus and options before saving configuration changes.

Configuration Overview​

Configuring the T356 for Plaspy prepares the unit to send stored and live telemetry to the Plaspy platform and ensures the device can offload records when it connects to configured Wi Fi networks. The process focuses on setting the Plaspy server endpoint, confirming transport settings, and validating that the T356 uploads its local records.

  • Point the tracker to the Plaspy server endpoint and port so uploads target the correct receiver.
  • Configure transport selection on the device if required by the configuration tool.
  • Ensure Wi Fi profiles and network credentials are present so the device can perform automated offload.
  • Apply and save changes, then validate the device is visible in Plaspy and uploading records.
  • Confirm immobilizer and OBD telemetry features remain functional after configuration save.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol when the device connects
  • Note that all devices in Plaspy use the same port for device data ingestion

Typical Requirements Before Setup​

  • Physical access to the vehicle to install or inspect the T356 OBD II plug unit and confirm power.
  • A configured Wi Fi network or access point used for automated offloads and firmware updates.
  • Access to the official Ulbotech configuration method such as the device web soft AP, manufacturer software, or USB configuration interface.
  • A charged device battery or stable vehicle power so the tracker remains powered during configuration and testing.
  • Knowledge of any required Wi Fi SSID and password credentials for depot or office networks.
  • Administrative access to the network that the device will use to reach d.plaspy.com if network restrictions exist.

How This Tracker Connects to Plaspy​

The T356 uploads stored records and near real time telemetry to the Plaspy server endpoint. When a configured Wi Fi access point is within range, the device performs an offload of buffered data and can also provide near real time updates while connected. Plaspy receives these uploads on the shared endpoint and automatically identifies the device protocol.

  • The tracker is configured to report to the shared Plaspy ingestion endpoint at d.plaspy.com or 54.85.159.138.
  • All data uploads from the device use port 8888 on the Plaspy server.
  • Transport may be UDP or TCP depending on the T356 configuration; Plaspy supports either and detects the protocol automatically.
  • Stored records are uploaded when the T356 connects to one of its configured Wi Fi profiles.
  • Plaspy processes location, OBD telemetry, and event reports for visibility and fleet dashboards.

Common Configuration Workflow​

  1. Access the official Ulbotech configuration method for the T356, such as the soft AP, web interface, or vendor configuration tool.
  2. In the server or reporting settings enter the Plaspy server address as d.plaspy.com or the IP 54.85.159.138.
  3. Set the device port to 8888 as the data ingestion port used by Plaspy.
  4. If the configuration tool requires choosing a transport protocol, select UDP or TCP as supported by the device.
  5. Add or confirm Wi Fi profiles and credentials used for automated offload so the device can upload stored records.
  6. Apply or save the configuration changes and restart the device if the interface requires a reboot.
  7. Validate that the T356 is reporting to Plaspy by observing device activity in your Plaspy account and confirming uploads reach the server.

Example Configuration Commands​

The T356 supports multiple manufacturer configuration paths and the exact commands or configuration screens vary by firmware and tool. Because Ulbotech firmware and configuration utilities may expose different interfaces, consult the official Ulbotech configuration guide for exact command syntax or menu locations. In general, the key public values you will enter are the Plaspy server domain d.plaspy.com or IP 54.85.159.138 and port 8888, and selecting UDP or TCP if required.

Configuration Notes​

  • Firmware differences can change menu structure and available features; always check the installed firmware version before following a workflow.
  • Choose UDP or TCP based on device options and network reliability; Plaspy will detect the protocol automatically when the device connects.
  • Because the T356 is Wi Fi first, ensure the access points used for offload allow outbound connections to d.plaspy.com or 54.85.159.138 on port 8888.
  • All Plaspy supported devices use the same ingestion port 8888 which simplifies multi device deployments.
  • Keep a backup of current configuration settings before making changes so you can restore a known good state if needed.

Why Use Plaspy with This Configuration​

Using the Ulbotech T356 with Plaspy provides a low operational cost telemetry solution for fleets that can leverage Wi Fi offload. The T356’s local storage, OBD II telemetry, and immobilizer outputs combine with Plaspy’s ingestion endpoint to deliver reliable location, vehicle data, and event reporting for fleet visibility and security workflows.

To learn more about Plaspy visit https://www.plaspy.com. For the latest device specific configuration methods, firmware notes, and manufacturer guidance verify details on the Ulbotech website http://www.ulbotech.com/. Manufacturer specifications and setup methods can change over time so confirm the current documentation before applying configuration changes.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy