Skip to main content

V-SUN - V-520 Configuration

This page documents the public configuration context for using the V-SUN V-520 tracker with the Plaspy platform. It summarizes the practical setup steps that are commonly used to prepare the V-520 to send location data to Plaspy, and it reproduces the publicly available SMS configuration commands that some installers and integrators use. The V-520 supports both SMS reporting and GPRS TCP reporting, and the manufacturer provides SMS command syntax for many common configuration tasks.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when the device connects. Exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor configuration tools, so use this guide together with the official V-SUN documentation and any installation notes from your supplier.

Configuration Overview​

The purpose of configuring the V-SUN V-520 for Plaspy is to direct the device to the Plaspy server endpoint, confirm data connectivity, and enable the tracker to report location and status reliably to the platform. Typical V-520 setups use SMS commands to set APN and GPRS server parameters, then enable GPRS mode so the device uploads position data.

  • Set the operator APN and optional APN credentials so the V-520 can attach to mobile data.
  • Point the device to the Plaspy server endpoint so location reports are uploaded.
  • Choose the transport protocol and port used by Plaspy and save the configuration.
  • Enable GPRS reporting and verify the device is visible in Plaspy.
  • Optionally set movement and static update intervals to control report frequency.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Plaspy automatically detects the tracker protocol when the device connects

These values are the shared Plaspy settings used for all compatible devices on the platform. When configuring the V-520, point its GPRS server settings to either d.plaspy.com or 54.85.159.138 and use port 8888. Select UDP or TCP as required by your device setup; Plaspy will detect the protocol automatically.

Typical Requirements Before Setup​

  • A charged and powered V-SUN V-520 with working SIM card inserted.
  • A SIM with active mobile data and the correct APN settings from the mobile operator.
  • Access to the device SMS command channel or the manufacturer configuration tool used by your vendor.
  • Knowledge of the device password if it differs from the default 0000.
  • A network environment that allows outbound data to the Plaspy server domain or IP.
  • Access to the official V-SUN documentation for firmware specific differences.

How This Tracker Connects to Plaspy​

The V-520 can upload positioning data to Plaspy via GPRS TCP or UDP. Once the device is configured with the Plaspy server endpoint and the mobile APN, it establishes a data session and begins sending periodic location reports to the shared Plaspy server on port 8888.

  • The tracker is configured to report to d.plaspy.com or 54.85.159.138 using port 8888.
  • Transport can be either UDP or TCP depending on the device configuration choice.
  • Plaspy automatically determines the tracker protocol when the connection is received.
  • Plaspy receives periodic position updates and exposes them in the platform for monitoring and history.
  • Event reporting and movement updates occur according to the device update intervals you configure.

Common Configuration Workflow​

  1. Access the official manufacturer configuration method or tool, typically SMS commands for the V-520 or vendor software if provided.
  2. Set the operator APN and any APN username or password required by the SIM operator.
  3. Enter d.plaspy.com or the server IP 54.85.159.138 as the GPRS server address.
  4. Set the port to 8888 and choose UDP or TCP if the device requires a transport selection.
  5. Apply or save the configuration and enable GPRS reporting on the device.
  6. Restart or power cycle the device if required by the tracker firmware to apply settings.
  7. Validate that the device reports to Plaspy by checking device visibility and recent position updates in the platform.

Example Configuration Commands​

The V-520 supports SMS based configuration using the device password. The public commands below are presented in the order found in the manufacturer supplied content. The device default password shown in these examples is 0000. If your device password has been changed, replace 0000 with the current password.

  • Factory reset (optional initial setup)
*RESET#0000##
  • Set the operator APN. Replace [apn] with your operator APN. If your APN requires username or password, replace [apnu] and [apnp] respectively. Use the format shown and include the extra fields only if required by your operator.
#803#0000#[apn]#[apnu]#[apnp]##
  • Set the GPRS server to the Plaspy IP and port. This points the tracker to Plaspy for GPRS uploads.
#804#0000#54.85.159.138#8888##
  • Set the moving update interval. Example sets the update interval used when the device is moving.
#805#0000#120#1##
  • Set the static update interval. Example sets the update interval used when the device is stationary.
#809#0000#120#1##
  • Enable GPRS mode so the device uploads data via mobile data services.
7100000
  • Enable GPS mode on the tracker if required by firmware or installation.
2220000

Notes on the placeholders

  • [apn] is the operator APN string required for mobile data connectivity.
  • [apnu] is the APN username when required by the operator.
  • [apnp] is the APN password when required by the operator.

Send each SMS from an authorized phone number if the device is configured to accept commands only from predefined numbers. After sending server and APN settings, enabling GPRS mode and restarting the device often helps ensure the new settings take effect.

Configuration Notes​

  • V-520 configuration is frequently performed via SMS commands, but vendor tools or PC software may also be available depending on firmware.
  • Firmware revisions and hardware variants can change command formats or required parameters; confirm with V-SUN documentation for your exact firmware.
  • Choose UDP or TCP based on your operational preference; Plaspy accepts either and will detect the protocol automatically.
  • Plaspy uses the same port 8888 for all supported devices, simplifying server configuration across a mixed device fleet.
  • When using SMS commands, the device password must be correct; the examples above show the default 0000 used in public guidance.

Why Use Plaspy with This Configuration​

Using Plaspy with the V-SUN V-520 gives you a centralized platform to view real time locations, historical tracks, and device status for portable trackers. Pointing the V-520 to the shared Plaspy server endpoint simplifies fleet or asset onboarding because the same server settings apply across supported devices and Plaspy handles protocol detection automatically.

Learn more about Plaspy and platform features at https://www.plaspy.com. Verify device specific setup details, firmware behavior, and the latest manufacturer commands with V-SUN at http://www.v-sun.cc/ since manufacturer specifications and setup steps can change over time.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy