Skip to main content

WanWay - G19S Configuration

This page covers the public configuration context for using the WanWay G19S GPS tracker with the Plaspy platform. It summarizes the practical server settings and the commonly used setup steps that let the G19S report location and device status to Plaspy. The guidance below uses only published configuration steps and the public Plaspy connection values.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol, while exact manufacturer side setup steps can vary by firmware version, hardware revision, installation type, and vendor tools. The G19S can be configured over SMS and GPRS according to WanWay public commands; use the official WanWay documentation and vendor tools for device specific details.

Configuration Overview​

This configuration prepares the G19S to send position and status updates to Plaspy by setting the device APN, server endpoint, reporting interval, and GPRS mode. The goal is to make the tracker visible and manageable inside Plaspy using the platform's shared endpoint and automatic protocol detection.

  • Set the carrier APN so the G19S can connect to mobile data for GPRS reporting.
  • Point the device at the Plaspy server endpoint so telemetry reaches the Plaspy platform.
  • Configure a reporting interval to control how often the tracker sends updates to Plaspy.
  • Enable GPRS mode on the tracker so it uses mobile data to transmit messages.
  • Verify configuration and device status with the tracker verification commands published by WanWay.

Plaspy Server Settings​

  • Server domain: d.plaspy.com
  • Server IP: 54.85.159.138
  • Port: 8888 (Plaspy uses the same port for all supported devices)
  • Transport: the device may be configured to use UDP or TCP on port 8888
  • Plaspy automatically detects the tracker protocol so the platform can accept connections from supported devices without separate protocol selection on the server side

Typical Requirements Before Setup​

  • A powered and installed WanWay G19S tracker with access to its SMS or configuration interface.
  • A SIM card inserted that supports mobile data and can send/receive SMS if using SMS configuration.
  • Carrier APN information for the SIM card to enable GPRS connectivity.
  • Access to the official WanWay configuration method, typically SMS commands or a WanWay configuration tool.
  • A Plaspy account or provisioning method to register and view the device once it reports to the platform.
  • A basic validation plan to confirm the device reports location after configuration.

How This Tracker Connects to Plaspy​

The WanWay G19S is configured to report location and status using GPRS to the shared Plaspy endpoint and port so data from the tracker appears inside the Plaspy platform. Plaspy's server accepts connections over the shared port and detects the tracker protocol automatically.

  • The tracker uses the configured APN to establish a GPRS data session.
  • Device telemetry is sent to d.plaspy.com (or the Plaspy server IP) on port 8888.
  • The tracker can be set to use UDP or TCP transport when transmitting to port 8888.
  • Plaspy receives the incoming data and maps it to the corresponding device using automatic protocol detection.
  • After successful connection, location updates and status messages become visible in Plaspy for monitoring and reporting.

Common Configuration Workflow​

  1. Gather the device, a working SIM with data and SMS capability, the SIM carrier APN, and access to WanWay setup instructions or tools.
  2. Use the official WanWay configuration method (SMS commands or vendor tool) to set the carrier APN so the tracker can open a GPRS session.
  3. Enter the Plaspy server values: d.plaspy.com (or 54.85.159.138) and set the port to 8888.
  4. If the device requires a transport choice, select UDP or TCP to match your network preference.
  5. Set a reporting interval (timer) appropriate for your monitoring needs and save or apply the configuration.
  6. Restart or power cycle the device if required by the firmware to activate the new settings.
  7. Validate that the device is reporting by checking device status with WanWay verification commands and confirming the device appears in Plaspy.

Example Configuration Commands​

The WanWay G19S supports SMS-based configuration. Below are the common public commands published for the G19S. Preserve the placeholders when sending commands.

  • Set carrier APN (replace [apn], and if required include username and password):
APN,[apn]{{# if apnu }} ,[apnu],[apnp]#{{/if}}

Example form as provided:

APN,[apn]

or when username and password are required:

APN,[apn],[apnu],[apnp]#
  • Configure the GPRS server to report to Plaspy (server entry followed by the port and any device parameter):
SERVER,1,d.plaspy.com,8888,0#
  • Set periodic reporting interval (example sets two timers, often used for fixed and moving intervals):
TIMER,60,60#
  • Enable GPRS mode on the device:
GPRSON,1#
  • Check current device configuration:
PARAM#
  • Check tracker status:
STATUS#

Notes about the commands above:

  • Keep the order: APN first, then SERVER, then TIMER, then enable GPRS. That sequence helps ensure the device has network connectivity before pointing it at the Plaspy server.
  • [apn], [apnu], and [apnp] are placeholders for your carrier APN, APN username, and APN password respectively. Replace them with the exact values from your mobile operator.
  • The SERVER command example uses d.plaspy.com and port 8888 as required by Plaspy.

Configuration Notes​

  • WanWay firmware versions and regional hardware variants can change the exact SMS syntax or parameter order; always check the latest WanWay documentation for your device revision.
  • SMS-based setup is a common public method for the G19S but vendor software or USB/serial tools may also be available; use the method recommended by your installer.
  • If your configuration interface asks for transport type, you may choose UDP or TCP; Plaspy accepts either on port 8888 and detects the protocol automatically on the server side.
  • Confirm APN credentials with the mobile operator before sending commands; incorrect APN is the most common reason GPRS reporting fails.
  • After applying settings, allow a short period for the device to register on the mobile network and for Plaspy to detect the incoming session.

Why Use Plaspy with This Configuration​

Using the WanWay G19S with Plaspy provides a straightforward path to real time visibility and operational monitoring. By pointing the G19S at the shared Plaspy endpoint and configuring a reliable reporting interval, organizations gain near real time tracking, status alerts, and route history in a single platform designed to accept diverse tracker protocols.

If you want to learn more about Plaspy and how the platform handles device connections and fleet visibility, visit https://www.plaspy.com. For the most current, device specific configuration steps, firmware notes, and technical references, verify setup details on the manufacturer site https://www.wanwaytech.net/ as device behavior and commands can change between firmware and hardware revisions.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy