Skip to main content

YulongDa - H08 Configuration

This page covers the public configuration context for using the YulongDa H08 GPS tracker with Plaspy. It focuses on the practical, public steps required to point the device at Plaspy servers and to validate basic reporting so the device becomes visible inside the Plaspy platform.

Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol when data arrives. Manufacturer side setup steps can vary by firmware version, hardware revision, installation type, or vendor configuration tools, so this guide combines the public Plaspy endpoint details with the common YulongDa H08 SMS commands and setup workflow shown in available public guidance.

Configuration Overview​

The goal of configuration is to prepare the H08 so it reliably sends location and status data to the Plaspy endpoint and appears in your Plaspy account. Below are the practical purposes of the configuration process:

  • Point the H08 to the Plaspy server endpoint and port so data is routed into the Plaspy platform.
  • Configure the device APN so the tracker has GPRS data connectivity to send packets.
  • Set update intervals used while moving and while stopped to control reporting frequency.
  • Validate connectivity and confirm the device is visible and reporting in Plaspy.
  • Preserve or record the device password used for remote commands when required.

Plaspy Server Settings​

  • Server domain d.plaspy.com
  • Server IP 54.85.159.138
  • Port 8888
  • Transport support for UDP or TCP
  • Automatic protocol detection in Plaspy so the platform recognizes the tracker protocol on receive

These exact values are the public Plaspy endpoint details to use when configuring the device to report to Plaspy. Plaspy uses the same port for all supported devices and automatically detects the tracker protocol.

Typical Requirements Before Setup​

  • Device powered and accessible for configuration either by SMS or the manufacturer configuration tool
  • A working SIM card with a data plan and the correct operator APN information
  • Knowledge of the device password used for SMS configuration; the example commands use the initial password 000000
  • Access to the device installation documentation from the manufacturer or vendor
  • A method to receive device responses such as an SMS capable phone or the installer console

How This Tracker Connects to Plaspy​

The H08 sends location and status data over GPRS to the configured Plaspy endpoint and port so that the device appears in the Plaspy platform. The device configuration instructs the tracker where to send packets and how often to report.

  • The tracker is pointed at the shared Plaspy server endpoint and port to deliver telemetry
  • Data is sent over GPRS using TCP or UDP depending on device selection and network behavior
  • Plaspy automatically detects the incoming tracker protocol and maps the device to your account feed
  • Regular and motion based reporting intervals determine how frequently location updates arrive
  • Visibility on Plaspy enables live tracking, event alerts, and operational monitoring

Common Configuration Workflow​

  1. Access the official YulongDa configuration method such as the SMS command interface or vendor configuration tool documented by the manufacturer.
  2. Enter the Plaspy server domain d.plaspy.com or the Plaspy server IP 54.85.159.138 as the GPRS server target.
  3. Set the server port to 8888 which Plaspy uses for all supported devices.
  4. Choose the transport mode UDP or TCP if the device requires a transport selection during setup.
  5. Apply or save the configuration on the device using the manufacturer method, for example by sending configured SMS commands.
  6. Restart the device if required by the firmware to activate new network settings.
  7. Validate that the device reports to Plaspy by checking the device listing or incoming telemetry in your Plaspy account.

If you are using SMS commands for initial setup, perform them in the order required by the device and verify each command response before proceeding.

Example Configuration Commands​

The following commands are extracted from public YulongDa H08 guidance. These are SMS style commands that assume the device accepts SMS configuration and that the initial device password is 000000 in the examples. Preserve the placeholders and replace them with your operator values as needed.

  • Set the operator APN
*APN#000000#[apn]#

If your APN requires a username or password include them in the command sequence like this

*APN#000000#[apn]#[apnu]#[apnp]#
  • Set the GPRS server to Plaspy using the public Plaspy server IP and port
*IP#000000#54.85.159.138#8888#
  • Set the update interval while moving to 60 seconds
XT60
  • Set the update interval while stopped to 60 seconds
NXT60

Notes on placeholders and values

  • [apn] is the operator APN string provided by your SIM carrier
  • [apnu] is the APN username when required by the carrier
  • [apnp] is the APN password when required by the carrier
  • The example uses the initial device password 000000; if your unit has a different password use that value instead
  • Use the commands in the order shown if following the manufacturer example, and confirm SMS responses from the device before proceeding

Configuration Notes​

  • Firmware and hardware revisions may change exact command syntax or available features; always confirm with the device response text or manufacturer notes.
  • The H08 supports SMS based configuration as shown in public guidance and may also accept configuration via vendor tools depending on the seller.
  • Choose TCP or UDP based on your network reliability and the device firmware guidance; Plaspy accepts either protocol on the shared port and will auto detect the protocol used.
  • Confirm APN and SIM data connectivity before updating server settings to avoid the device losing remote access.
  • Keep a record of the device password and any changes made during setup for future management.

Why Use Plaspy with This Configuration​

Configuring the YulongDa H08 to report to Plaspy gives organizations a straightforward way to centralize vehicle location and status reporting using a shared, publicly documented server endpoint. With the H08 pointed at Plaspy and reporting on a regular interval, fleet managers can gain visibility into movement, receive alerts, and monitor operational status through the Plaspy platform.

Learn more about Plaspy on the main website https://www.plaspy.com. Device specific configuration steps, firmware behavior, and manufacturer details can change over time so verify the latest setup information from the manufacturer at http://www.yulongdatechnology.com.

Tracker Configuration

Need a platform for this tracker setup

Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.

Learn more about Plaspy