Autoseeker - AT-15 Protocol
This page summarizes the public protocol context for using the Autoseeker AT-15 tracker with the Plaspy platform. It focuses on how the AT-15 communicates with Plaspy in general terms and what to check when configuring devices for reliable reporting. This guidance is intended to help administrators and integrators understand connection basics and common considerations without exposing firmware internals.
Plaspy uses shared connection settings across supported devices and automatically detects the tracker reporting protocol when a device is correctly pointed at the Plaspy endpoint. Exact protocol behavior can vary by firmware version, hardware revision, or manufacturer implementation, so device behavior may differ between units or after firmware updates.
Protocol Overview
The tracker reporting protocol is the formal set of messages and connection behaviors that allow the AT-15 to send location, status, and event data to a server like Plaspy. In public documentation terms, the protocol defines how the device identifies itself, how position and alert information is reported, and how the server acknowledges or records those reports.
- Enables the AT-15 to transmit GPS fixes, timestamps, and basic status indicators to a remote server.
- Carries events such as geofence enters and exits, movement alerts, and power or battery notices.
- Provides device identity information so Plaspy can associate incoming reports with the correct unit.
- Supports periodic reporting and event driven messages that keep location and status current in Plaspy.
- Allows for configuration commands from the manufacturer or commissioning tools when device support exists.
How Plaspy Detects the Protocol
Plaspy receives device traffic on a shared public endpoint and automatically identifies the tracker protocol used by incoming connections. When an AT-15 is configured to report to Plaspy, the platform will match the incoming device messages to known protocol patterns and route the data appropriately.
- Plaspy listens on a standard endpoint so users do not normally need to select a protocol manually.
- Ensure the AT-15 is configured to report to Plaspy to allow automatic detection to occur.
- Plaspy uses the same port for all supported devices which simplifies device configuration.
- Correct device identity and consistent reporting intervals improve automatic detection reliability.
- If a device is not detected automatically, confirming the device is pointed at the Plaspy endpoint is a useful first step.
Transport and Connection Context
The transport layer determines how the AT-15 opens a session to Plaspy and how messages are transmitted. The device may be configured to use either of the common transport protocols depending on its firmware and settings, and Plaspy accepts both transport types on the shared port.
- Devices may be configured to use UDP or TCP on port 8888 depending on the device support and configuration options.
- The Plaspy server endpoint for device reporting is d.plaspy.com and the public server IP is 54.85.159.138.
- All devices supported by Plaspy use the same port which reduces configuration complexity across mixed fleets.
- Select UDP when low overhead and occasional packet loss is acceptable; select TCP when reliable delivery and session state are preferred, subject to device capability.
- Confirm the device is set to report to d.plaspy.com or 54.85.159.138 on port 8888 as a standard commissioning step.
Protocol Compatibility Notes
- Firmware revisions can change message timing, available events, and supported transports; always verify the firmware level on your AT-15 units.
- Hardware revisions or aftermarket variants may implement slightly different behavior that affects message content or reporting intervals.
- Manufacturer configuration tools or SMS/command interfaces can change how the device reports to servers; document any changes made during deployment.
- Transport selection (UDP vs TCP) should align with device capability and the network environment where the tracker will operate.
- If integrating many units, validate a small batch before a full rollout to catch any unexpected protocol or transport differences.
- Always cross check device behavior against official manufacturer documentation when possible.
Why Protocol Understanding Matters
A practical understanding of the device communication protocol helps ensure successful setup, efficient troubleshooting, and predictable operation over time. Knowing the essentials of how the AT-15 reports location and events to Plaspy reduces guesswork and supports smoother fleet or asset management.
- Helps troubleshoot connectivity issues by confirming correct endpoint and transport settings.
- Improves commissioning by ensuring devices are pointed at the Plaspy endpoint and using the intended transport.
- Enables better battery and reporting schedule decisions by understanding how report frequency affects power use.
- Supports reliable geofence and alert behavior through consistent reporting and event handling.
- Makes it easier to validate whether firmware updates or hardware changes affect operational behavior.
Why Use Plaspy with This Protocol
Using Plaspy with the Autoseeker AT-15 provides a straightforward path to collect real time location, geofence events, and basic status information across a mixed set of trackers. Plaspy’s shared endpoint approach and automatic protocol detection simplify device setup and reduce the need for per device port management, which is helpful when deploying units at scale or managing multiple tracker models.
If you need more details about Plaspy features or deployment options, learn more on the Plaspy website at https://www.plaspy.com. For the most current and device specific protocol documentation, firmware notes, and manufacturer guidance for the Autoseeker AT-15, verify details on the official Autoseeker site at https://autoseekergps.com/ because protocol support and device behavior can change over time.
Tracker Communication
Looking for a platform that works with compatible protocols
Plaspy helps receive data from supported trackers and organize monitoring, visibility, and reporting in one place.