Meitrack - MVT-600 Protocol
This page describes the public protocol context for using the Meitrack MVT-600 tracker with Plaspy. It focuses on high level communication and integration information that helps operators and integrators understand how the device reports telemetry, events, and accessory data into Plaspy without exposing implementation sensitive details.
The Meitrack MVT-600 offers features such as optional invehicle camera snapshots, fuel sensor inputs, RFID authentication, geo fencing, SOS alerts, AGPS assisted positioning, and remote engine control. Plaspy uses shared connection settings across supported devices and automatically detects the tracker protocol while exact protocol behavior can vary by firmware version, hardware revision, and manufacturer implementation.
Protocol Overview
At a high level the tracker protocol defines how the MVT-600 sends identification, location, status, and event data to a remote server and how the server can optionally send responses or commands. Understanding this public context clarifies what information the device can provide to Plaspy and what to check during setup.
- The protocol enables the device to identify itself and transmit GPS coordinates, timestamps, and sensor states to the server.
- Event reporting supports accessories such as camera triggers, fuel sensor alerts, RFID events, and SOS activations.
- Telemetry and event data are delivered to Plaspy where it is parsed into usable location, diagnostic, and alert records.
- The protocol also allows for server initiated messages where supported by the device and configuration.
- Behavior and available event types can differ based on firmware or optional accessories installed on the device.
How Plaspy Detects the Protocol
Plaspy receives incoming connections at a shared Plaspy endpoint and uses the incoming data to determine the device protocol automatically. In typical setups users do not need to select a protocol inside Plaspy when the device is pointed to the correct Plaspy endpoint and port.
- Plaspy listens on the same port for all supported devices which simplifies device configuration and routing.
- Devices can be pointed to the Plaspy server by domain or by IP address to reach the Plaspy endpoint.
- If a device is configured to report properly to the Plaspy endpoint, Plaspy will automatically detect the tracker protocol without manual selection.
- Proper device identification during first contact helps Plaspy map messages to the correct device record in an account.
- Confirming device reporting frequency and event triggers on the tracker helps Plaspy reliably detect and classify incoming messages.
Transport and Connection Context
Transport and connection settings determine how MVT-600 messages are delivered to Plaspy. The MVT-600 may support different transport modes depending on firmware and local configuration, and these choices affect connection reliability and message behavior.
- The device may be configured to use UDP or TCP on port 8888 depending on device support and configuration.
- Devices can be pointed to the Plaspy server using the domain d.plaspy.com or the server IP 54.85.159.138.
- Plaspy receives device traffic on port 8888 and uses that single port for all connected tracker types.
- Choosing UDP can favor low latency reporting while TCP can favor delivery confirmation when the device and network conditions are appropriate.
- Network level considerations such as NAT, firewall rules, and mobile operator behavior can influence which transport mode works best.
Protocol Compatibility Notes
- Firmware revisions on the MVT-600 can change available fields, optional accessory reporting, and event names; always verify the firmware revision in use.
- Hardware revisions and optional modules such as camera, fuel sensors, or RFID readers may add or remove event types and telemetry fields.
- Some features, like remote engine stop or listen in, may require additional configuration on the device and proper authorization on the server side.
- Transport selection between UDP and TCP can affect how events are delivered and whether server responses are reliable.
- Manufacturer settings such as APN, server address, and reporting intervals must be set correctly for Plaspy to receive data.
- Confirm compatibility against official Meitrack documentation and changelogs when troubleshooting unusual behavior.
Why Protocol Understanding Matters
A practical understanding of the MVT-600 communication protocol helps operators set up devices correctly, verify successful reporting, and diagnose issues that affect location accuracy, event reporting, and accessory integration.
- Ensures the device is configured to point at the correct Plaspy endpoint so messages arrive reliably.
- Helps troubleshoot missing events such as camera snapshots, fuel sensor alerts, or RFID access reports by focusing on transport and firmware differences.
- Guides decisions about UDP versus TCP based on network behavior, latency needs, and message reliability.
- Reduces time spent on support by confirming which features depend on firmware, accessory modules, or manufacturer configuration.
- Supports planning for firmware updates and hardware rollouts across a fleet to maintain consistent behavior.
Why Use Plaspy with This Protocol
Using the Meitrack MVT-600 with Plaspy provides a consolidated way to collect location, event, and accessory data from vehicles and present it for operations, monitoring, and fleet management. Plaspy ingests telemetry and event reports so teams can track vehicle location, receive timely alerts for critical events, and access historical logs for reporting and compliance.
Plaspy is designed to simplify device onboarding by using a shared server endpoint and a single port for all supported trackers. To learn more about Plaspy and how it works with devices like the MVT 600 visit https://www.plaspy.com. For the most current and device specific protocol details, firmware notes, and accessory compatibility please verify information on the manufacturer website https://www.meitrack.com/ as protocol support and firmware behavior can change over time.
Tracker Communication
Looking for a platform that works with compatible protocols
Plaspy helps receive data from supported trackers and organize monitoring, visibility, and reporting in one place.