Skip to main content

Meitrack - VT-300 Protocol

This page provides a public protocol overview for using the Meitrack VT-300 with Plaspy. It focuses on high level communication context and practical compatibility considerations rather than internal or sensitive implementation details. The VT-300 is a vehicle GPS/GSM/GPRS tracker with SMS and GPRS TCP/UDP reporting capabilities and support for the Meiligao protocol family for over the air reporting.

Plaspy uses shared connection settings across supported devices and automatically detects the tracker protocol. Devices that report correctly to the Plaspy endpoint will typically be identified without manual protocol selection. Exact behavior and available commands can vary by firmware version, hardware revision, and manufacturer implementation, so confirm device specifics where necessary.

Protocol Overview​

The protocol used by the VT-300 defines how the tracker identifies itself, reports location and status, and transmits alarms or telemetry to a remote server. In practical terms for integration with a tracking platform like Plaspy, that means the protocol governs the format and timing of messages the device sends and how the platform interprets those messages into position, speed, alarm, and IO state information.

  • Identifies the device to the server so incoming messages can be associated with a vehicle or asset.
  • Sends periodic position reports and movement updates that the platform converts into location tracks.
  • Transmits status and alarm events such as SOS, geo fencing, low battery, or engine cut indicators.
  • Supports multiple transport options for GPRS reporting and can fall back to SMS for certain commands or alerts.
  • Works in combination with assisted GPS features such as AGPS and GSM base station information to improve fix reliability.

How Plaspy Detects the Protocol​

Plaspy receives tracker reports at a single shared endpoint and port and automatically detects the tracker protocol from the incoming connection and device identification. In most cases a properly configured VT-300 will start sending usable reports to Plaspy without requiring protocol selection in the platform.

  • Plaspy listens on a shared server endpoint so devices only need to point to the same host and port.
  • The Plaspy server domain is d.plaspy.com and the public server IP is 54.85.159.138 for device configuration.
  • Plaspy uses a single port for all devices and automatically detects the tracker protocol when reports arrive.
  • Users typically do not need to select a protocol inside Plaspy if the device is configured to report to the Plaspy endpoint.
  • Proper device identification in the first reports helps Plaspy associate data with the correct account and asset.

Transport and Connection Context​

The VT-300 can transmit data over GPRS using either UDP or TCP depending on device support and user configuration. When integrating with Plaspy, configure the device to report to Plaspy's shared endpoint and port so the platform can receive and process messages consistently.

  • Devices may be configured to point to d.plaspy.com or to the numeric server address 54.85.159.138.
  • The Plaspy port for tracker reporting is 8888 and all devices in Plaspy use the same port.
  • The VT-300 supports reporting over GPRS TCP or UDP on port 8888; choose the transport that matches your carrier and network conditions.
  • SMS remains an alternative channel for certain device features and out of band commands when supported.
  • Network stability, APN settings, and correct transport selection affect how reliably positions reach the platform.

Protocol Compatibility Notes​

  • Manufacturer firmware versions can change message formats or available features; always confirm firmware and release notes for the VT-300.
  • Hardware revisions or regional variants may alter supported transports or optional sensors.
  • The VT-300 commonly uses the Meiligao protocol family for SMS and GPRS reporting; reference manufacturer materials for exact command lists.
  • Transport selection TCP versus UDP can affect delivery semantics and should be matched to your server configuration.
  • Some features such as AGPS or GSM base station reporting can influence position performance but depend on device configuration and network support.
  • Test devices in a controlled setting before wide deployment to validate behavior with your carrier and with Plaspy.

Why Protocol Understanding Matters​

A practical understanding of the VT-300 communication protocol helps ensure successful setup, reliable reporting, and faster troubleshooting when integrating devices with Plaspy. Knowing the high level behavior and configurable options reduces integration time and helps maintain consistent fleet visibility.

  • Ensures you configure APN, transport, and server settings so the device can reach Plaspy reliably.
  • Helps interpret device events and map them to the platform's alarm and reporting features.
  • Makes it easier to diagnose connectivity issues between the tracker and Plaspy when reports are missing or intermittent.
  • Guides decisions about reporting intervals and power management to balance battery life and location fidelity.
  • Clarifies when manufacturer firmware updates or configuration changes may affect deployed devices.

Why Use Plaspy with This Protocol​

Using the Meitrack VT-300 with Plaspy provides a straightforward way to collect vehicle location, status, and alarm events into a centralized fleet monitoring platform. The VT-300’s GPS sensitivity and feature set such as SOS, geo fencing, and engine cut combine with Plaspy’s shared endpoint approach to simplify device onboarding and data collection.

Plaspy automatically detects the tracker protocol and uses a single shared port for all supported devices, which reduces configuration complexity for fleets with mixed hardware. To learn more about Plaspy and how it can connect to your VT-300 devices visit https://www.plaspy.com. For the most current device protocol details, firmware behavior, and implementation notes check the official Meitrack documentation at https://www.meitrack.com/ as manufacturer support and firmware features can change over time.

Tracker Communication

Looking for a platform that works with compatible protocols

Plaspy helps receive data from supported trackers and organize monitoring, visibility, and reporting in one place.

Learn more about Plaspy