QuecLink - GV58LAU Configuration
This page documents the public configuration context for using the QuecLink GV58LAU tracker with Plaspy. It focuses on the practical server and setup details that are shared publicly, and explains how to point the device at Plaspy so position and event data are delivered to the platform. Where manufacturer commands or example steps are public, they are presented here to help you complete a basic integration.
Plaspy uses shared server settings across supported devices and automatically detects the tracker protocol to simplify device onboarding. Manufacturer-side setup steps can vary by firmware revision, hardware variant, installation type, and vendor tools, so use the commands and workflow here as a practical, public starting point and verify any device-specific differences with official QuecLink documentation.
Configuration Overview
The goal of configuration is to prepare the GV58LAU to reliably report GNSS location and device events to Plaspy and to validate connectivity after installation. Typical configuration prepares network access, points the tracker to Plaspy, and confirms that the device is visible in the platform.
- Configure the device to use Plaspy as the reporting server so position and event data reach Plaspy dashboards.
- Set the device APN and any required cellular credentials so GPRS/LTE sessions can establish.
- Apply the Plaspy server host and port so the tracker knows where to send TCP or UDP uplinks.
- Validate connectivity with live telemetry and confirm the device appears in Plaspy.
- Optionally use SMS based configuration if the device is accessible only by text commands during installation.
Plaspy Server Settings
- Server domain d.plaspy.com
- Server IP 54.85.159.138
- Port 8888
- Transport support for UDP or TCP
- Plaspy automatically detects the tracker protocol
These values are the public endpoint and port that GV58LAU devices should be configured to report to when integrating with Plaspy.
Typical Requirements Before Setup
- A powered and correctly wired GV58LAU device with cellular connectivity enabled.
- A valid cellular SIM card with data and correct APN settings for your operator.
- Access to the manufacturer configuration method supported by the device such as SMS commands or USB/service tools.
- Knowledge of the device password if required for configuration; the public default password in examples below is queclink.
- A way to receive device responses or telemetry (SMS replies, serial/USB logs, or Plaspy visibility) to confirm settings.
- Confirmation of firmware version and hardware revision where possible, since commands and behavior can vary.
How This Tracker Connects to Plaspy
When configured, the GV58LAU sends GNSS fixes and event reports to the shared Plaspy endpoint using standard uplink methods supported by the device. Plaspy ingests the device uplinks and maps location, I/O events, and configured alarms into the platform for live tracking and historical analysis.
- The tracker is configured to report to the shared Plaspy server endpoint at d.plaspy.com and its IP 54.85.159.138 on port 8888.
- The device can use either UDP or TCP transport to send uplinks depending on configuration preference; Plaspy supports both and will auto detect the protocol.
- Location updates, alarm triggers, and input/output events are submitted as uplink packets to Plaspy for dashboarding and notifications.
- Plaspy provides visibility and status monitoring once the tracker successfully connects and begins reporting to the shared endpoint and port.
Common Configuration Workflow
- Access the official QuecLink configuration method for your GV58LAU unit such as SMS commands, service tool, or USB interface.
- Set the device APN and any operator credentials required so the tracker can establish an LTE data session.
- Enter the Plaspy server as either the domain d.plaspy.com or the server IP 54.85.159.138.
- Set the port value to 8888 as the destination port used by Plaspy.
- Choose UDP or TCP if the device requires explicit transport selection; either is supported and Plaspy auto detects the protocol on arrival.
- Apply or save the configuration and restart the device if the device requires a reboot to apply changes.
- Validate that the tracker reports to Plaspy by confirming device presence and telemetry in the Plaspy platform.
Example Configuration Commands
The GV58LAU may be configured by sending SMS commands. The following public example commands are provided as a practical starting point. The example uses the device password queclink which is the default shown in the public commands. Preserve placeholders when applying these commands for your operator.
- Optional factory restore command for initial setup or to clear previous settings
AT+GTRTO=queclink,4,,,,,,FFFF$
- Labels: optional initial setup command to restore factory behavior when required. Use only when you intend to reset the device.
- Set the device time zone to UTC 0
AT+GTTMA=queclink,+,0,0,0,,,,,,FFFF$
- Set the operator APN and credentials
AT+GTBSI=queclink,[apn],[apnu],[apnp],,,,,FFFF$
- Placeholders explanation:
- [apn] is the mobile operator APN name
- [apnu] is the APN username if required by the operator
- [apnp] is the APN password if required by the operator
- Set the GPRS server to Plaspy by domain and IP with port 8888
AT+GTSRI=queclink,4,,1,d.plaspy.com,8888,54.85.159.138,8888,,0,0,0,,,,FFFF$
- This command configures the device to report to the Plaspy server at d.plaspy.com and the IP 54.85.159.138 using port 8888. It keeps both domain and IP targets as provided to support DNS or direct IP connectivity.
- Set the update reporting interval to 60 seconds
AT+GTFRI=queclink,1,1,0,0,,,60,60,60,60,7F,40,0,,,FFFF$
- Adjust the 60 second values if your installation requires different reporting frequency.
- Enable SOS button notification on input 2
AT+GTSOS=queclink,2,2,,0,0,0,0,0,0,,,FFFF$
- This configures SOS input behavior to generate notifications when triggered.
Note about SMS configuration
- SMS-based setup is shown here because the example public commands use SMS. Some installations prefer USB or a manufacturer toolkit; always follow the method that matches your device access and policy.
Configuration Notes
- Firmware and hardware revisions can change command syntax and available parameters. Verify exact command support for your GV58LAU firmware before mass deployment.
- The GV58LAU example above uses SMS commands and a default password queclink shown in public documentation. Change device passwords from defaults in production deployments when possible.
- Both TCP and UDP transports are supported by Plaspy and by the device configuration workflow; choose transport based on network and reliability preferences.
- Keep APN credentials and SIM provisioning ready prior to applying GPRS server settings so the device can immediately establish connectivity.
- When a command contains placeholders such as [apn], replace them with operator-specific values; do not include the curly braces in the final SMS.
Why Use Plaspy with This Configuration
Configuring the GV58LAU to report to Plaspy provides a practical path to real-time location, I/O event monitoring, and alarm handling for fleet and security workflows. Using the shared Plaspy endpoint and the sample SMS commands above you can prepare devices to deliver continuous telemetry and event alerts into a single platform that scales from a few vehicles to large fleets.
To learn more about Plaspy visit https://www.plaspy.com and for the latest device specific details and firmware notes consult the manufacturer at https://www.queclink.com/. Manufacturer specifications, setup methods, and firmware behavior can change over time so it is recommended to verify commands and procedures on the official QuecLink documentation before large scale deployment.
Tracker Configuration
Need a platform for this tracker setup
Plaspy helps you connect compatible trackers, receive device data, and centralize monitoring from one GPS tracking platform.