Reachfar - RF-V32 Protocol
This page summarizes the public protocol context for using the Reachfar RF-V32 GPS tracker with the Plaspy platform. It focuses on how the device communicates in broad, non sensitive terms and what to expect when integrating the RF-V32 for pet and livestock tracking using Plaspy.
Plaspy uses shared connection settings across supported devices and automatically detects the tracker protocol when a device reports to the Plaspy endpoint. Exact protocol behavior for the RF-V32 can vary depending on firmware version, hardware revision and manufacturer implementation, so this page describes the protocol role and transport context rather than device internals.
Protocol Overview
The RF-V32 reporting protocol enables the tracker to deliver location, status and alarms to a remote platform like Plaspy. In general terms, the protocol covers how the tracker identifies itself, how position and telemetry are encoded for transmission, and how alarm or status events are reported for use in a tracking platform.
- Allows the device to send location fixes and fallback positioning such as LBS A-GPS and WiFi indications to Plaspy
- Carries alarm and status events for geofence breaches, low battery and SIM change alerts
- Provides a device identifier and timing information so Plaspy can associate messages with the correct asset
- Supports periodic and event driven reporting so Plaspy can display real time location and historical traces
- Enables basic remote configuration commands where supported by the device and manufacturer
How Plaspy Detects the Protocol
Plaspy listens on a single shared endpoint so that devices can report without manual protocol selection in the platform. When the RF-V32 is configured to report to Plaspy, the platform receives the incoming reports and automatically matches the messages to a compatible protocol handler based on the data the device sends and the known set of supported formats.
- Plaspy accepts device reports on the shared server endpoint d.plaspy.com
- The Plaspy server IP address is 54.85.159.138 and the platform listens on port 8888
- Devices may be configured to use UDP or TCP to send data to Plaspy on port 8888
- All devices in Plaspy use the same port so endpoint configuration in the tracker is consistent across models
- If the RF-V32 is correctly configured to report to the Plaspy endpoint, users typically do not need to manually select a protocol inside Plaspy
Transport and Connection Context
Connection settings are a key part of successful integration. The RF-V32 supports GPRS TCP IP reporting and SMS based reporting as described by the manufacturer. When using Plaspy for online tracking, configure the device to send its GPRS reports to the Plaspy endpoint.
- RF-V32 can report over GPRS TCP IP to a remote server and can fall back to SMS for messages where supported
- For Plaspy integration set the device to report to d.plaspy.com or to the server IP 54.85.159.138
- The common Plaspy listening port for all devices is 8888 and the tracker may use either UDP or TCP on that port depending on device capability
- Ensure the device APN and GPRS session are active so the tracker can open a TCP or UDP session to the Plaspy endpoint
- Using the same port and a shared endpoint simplifies device configuration and reduces per device platform setup steps
Protocol Compatibility Notes
- Protocol behavior can change across firmware versions so verify the firmware revision if a device behaves differently than expected
- Hardware revisions or regional variants of the RF-V32 can implement reporting differences that affect compatibility
- Transport choice matters some devices or carrier networks handle UDP and TCP differently so try the transport that matches the device configuration and network environment
- Manufacturer settings such as reporting intervals and alarm enablement influence what Plaspy receives and displays
- Always validate tracker settings including server address and transport to ensure reports reach d.plaspy.com on port 8888
- Because the RF-V32 has been listed as out of production on the product page, availability and ongoing firmware updates may be limited
Why Protocol Understanding Matters
A clear understanding of the RF-V32 communication protocol helps ensure reliable setup, timely troubleshooting and predictable behavior in Plaspy. Knowing which parts of the protocol are fixed versus those that vary by firmware lets administrators make targeted configuration changes and interpret device behavior correctly.
- Helps confirm the device is pointed to the correct Plaspy endpoint and port for online reporting
- Aids troubleshooting when location updates or alarms do not appear in Plaspy by focusing checks on transport and device configuration
- Improves geofence and alarm tuning when reporting intervals and event thresholds are understood
- Supports planning for battery life and reporting cadence trade offs that affect long term deployments
- Clarifies when manufacturer firmware updates or device replacements are required for feature needs
Why Use Plaspy with This Protocol
Using the RF-V32 with Plaspy provides a straightforward way to gain real time visibility and historical trace playback for pet and livestock monitoring. The RF-V32’s GPS A-GPS LBS and WiFi fallback capabilities combined with Plaspy’s unified ingestion let owners and managers monitor locations, receive alarms and review movement history from a single platform.
To learn more about Plaspy and how the platform supports devices like the RF-V32 visit https://www.plaspy.com. For the latest device specific protocol documentation, firmware notes and manufacturer guidance verify details on the official Reachfar support site https://www.reachfargps.com/ as protocol support and firmware behavior can change over time.
Tracker Communication
Looking for a platform that works with compatible protocols
Plaspy helps receive data from supported trackers and organize monitoring, visibility, and reporting in one place.